phone mount for f150 3d models

The initial concept revolves around an iPhone 8 paired with a sleek Spigen slim case.

Use any filament that can take indoor car temps. Please feel free to remix mounts that fit on the truck mount to match your qi charger, mag safe etc.  Parts:Anker MagGo 610 ring2x m3x5bhcs or longer to lock in the ring and keep mag holder from...

Phone mount for my F150. Bolts on, as I didn't like the vent-mounts. ...Printed in ABS as PLA melted quite quickly.

[Here is the magnet phone mount I...

Goes in the rectangular slot beside the cup holders, secure with hot glue. ...Tested with 2015 Ford F150 supercab and 2021 Ford F350 supercrew, both with bench seats.

Center console phone cradle w/usb cable pass-through. Slide it into the track of the retractable door. ...The door holds it securely.

Center console phone cradle w/usb cable pass-through. Slide it into the track of the retractable door. The door holds it securely. ... If you like the design, please consider a tip: https://www.paypal.com/paypalme/thisrudager

... to seamlessly pair with JL Audio's top-of-the-line tweeter, ensuring an exceptional listening experience. The second mount is fabricated without pre-drilled holes, allowing for flexibility and adaptability when mounting alternative tweeters.

Hello All, I'm writing this review specifically for those seeking a large phone holder designed to fit the unique trapezoidal air vents found in Ford F-Type Trucks. This product is perfect for anyone looking to hang their phone from these vents.

first attempt at designing a thing this is for the 2019 Ford F150 to hold a cell phone on the dashboard above the steering column i haven't printed it yet so adjust you settings to suit.

This fits an Iphone 14max its about 3.25 inches in width for other phone comparison. Super Glued to bond parts. Recommended PetG or other high temp material if your in a hot location. The Base can be printed without SUPPORTS. I have done it and even...

I had an old charging pad that was slim like this one https://www.amazon.com/dp/B07DFFJDVY/ref=sspa_dk_detail_1?psc=1 It fits perfectly into the small opening above the nav screen on 2011-2014 F150's. I used velcro to hold the pad and ran power to...

Dashboard Mount for Galaxy Note 10 Plus (Kickstand case, or without) - Works with Other Phones Too Open it up to fit your phone, the opening is 12.2mm wide, perfect size. New Update: Now you can choose from two different sizes, one fits larger...

Phone holder to replace useless coin holder installed in older 2WD F-150s (2013 and similar). Must use PETG or equivalent material to prevent melting in hot cars. Your experience if printed in PLA will not end well. Designed to use 3mm screws and...

F150 switch panel mount for Auxbeam 8 gang switch panel v1 is plain without counter sink holes v2 is plain with counter sink holes v3 is v2 with a rounded top

Slide the mount and put your phone cord in it before inserting the tray and the mount back into the console. It basically wedges into place and makes a tight fit so no pot holes or sudden movements will dislodge it.Update: I made a shorter version...

Then the holder screws on top of the vent mount.(3MMx 10 MM screws) 2 holes provided for locating pins. I used wood dowels but you could print those too. Print in ASA or ABS or other high temp material. PLA will melt on a hot day. Included the...

Uses M5 nuts and bolts. ... For parts and pieces: https://www.thingiverse.com/thing:2194278 Single mount and Double mount versions.

Uses M5 nuts and bolts. ... For parts and pieces: https://www.thingiverse.com/thing:2194278 Single mount and Double mount versions. ... If you like the design, please consider a tip: https://www.paypal.com/paypalme/thisrudager

Ball Size 13mm Ender 3 Print Infill 30% 3 wall layer Top layer 3 Print time 1hr 11min

Cell phone vent holder F150  for moto 4  1.0mm nozzle  PLA, scale height 85.598mm.

F150 phone holder for my galaxy s9. ...Inside dimension is 85mm x 170mm

I've just adjusted the tray size for a friend's request, but I haven't printed anything yet. Along with this message, I'm attaching the original SketchUp file with square corners to make resizing even simpler. If you'd like to resize it and round off...

Fits an IWB soft holster for a pocket pistol and a spare magazine holder as well. Used rivets to attach to the inside of the center console in my truck. Several versions made while refining the design. My center console was not flat on one side so...

... Attach a backup camera, rearview camera or GoPro to the roof of your 2018-2020 F150. May fit older or newer trucks. Great for towing. Should work with most small waterproof cameras. Follows the contour of the light housing. Uses minimal filament.

Attach a backup camera, rearview camera or GoPro to the roof of your 2018-2020 F150. May fit older or newer trucks. Great for towing. Should work with most small waterproof cameras. Follows the contour of the light housing. Uses minimal...

I took inspiration from another user's clamp design and merged it with a custom mount I created for my 2010 F150's dashboard. With no good spot to secure a phone holder, this solution was the best option - it left no screw holes, velcro, or scratch...

This prompted me to design a custom tray that could accommodate not only my phone but also my MC-02A QI charger, available for purchase on eBay. The tray is versatile and can be used with or without the charger, accommodating even larger phones like...

The mount was crafted to perfectly fit my phone when it's in its case, but since it's tailored specifically for that size, I'm not sure how universal it is. However, the design might inspire others to create their own similar mount. ... To build this...

[GitHub Repository](https://github.com/zanovis/phone-mount) This is a phone mount which rests on the top-right side of a laptop. The top flange should retain the device if the laptop is moving around slightly (on lap, moving laptop from room to...