phone holder f150 3d models

Cell phone vent holder F150  for moto 4  1.0mm nozzle  PLA, scale height 85.598mm.

first attempt at designing a thing this is for the 2019 Ford F150 to hold a cell phone on the dashboard above the steering column i haven't printed it yet so adjust you settings to suit.

... material if your in a hot location. The Base can be printed without SUPPORTS. I have done it and even have a timelapse of it. The top phone holder unfortunately does have overhangs on the bottom feet. UPDATE: Added a shortened version of the base!

Phone holder to replace useless coin holder installed in older 2WD F-150s (2013 and similar). Must use PETG or equivalent material to prevent melting in hot cars. Your experience if printed in PLA will not end well. Designed to use 3mm screws and...

I had an old charging pad that was slim like this one https://www.amazon.com/dp/B07DFFJDVY/ref=sspa_dk_detail_1?psc=1 It fits perfectly into the small opening above the nav screen on 2011-2014 F150's. I used velcro to hold the pad and ran power to...

Dashboard Mount for Galaxy Note 10 Plus (Kickstand case, or without) - Works with Other Phones Too Open it up to fit your phone, the opening is 12.2mm wide, perfect size. New Update: Now you can choose from two different sizes, one fits larger...

This is a phone holder that specifically fits a ford F150 truck console. If your shifter is behind your steering wheel you most likely have a big opening with a rubber tray next to you. This mount slides into that rubber tray after you take the tray...

With no good spot to secure a phone holder, this solution was the best option - it left no screw holes, velcro, or scratch marks behind. Printed at 30% infill with PETG, it works flawlessly! My iPhone 6, encased in its protective shell, fits snugly...

Then the holder screws on top of the vent mount.(3MMx 10 MM screws) 2 holes provided for locating pins. I used wood dowels but you could print those too. Print in ASA or ABS or other high temp material. PLA will melt on a hot day. Included the...

F150 phone holder for my galaxy s9. ...Inside dimension is 85mm x 170mm

Hello All, I'm writing this review specifically for those seeking a large phone holder designed to fit the unique trapezoidal air vents found in Ford F-Type Trucks. This product is perfect for anyone looking to hang their phone from these vents.

... .5mm gap on both sides. Now I can hold two phones and chargers when someone wants to ride in truck. Wife is slightly happier.. Covers passenger cup holder is only drawback. I'm using this charger, its perfect. Ive been using it for 3 years.

Use any filament that can take indoor car temps. Please feel free to remix mounts that fit on the truck mount to match your qi charger, mag safe etc.  Parts:Anker MagGo 610 ring2x m3x5bhcs or longer to lock in the ring and keep mag holder from...

This is a ball joint adapter for the useless coin holder on my 2023 f150 lightning. I used the ball joint from this phone holder. There's 3 screws to remove from the back of the ball joint assembly to access it, then I cut about 10mm from the...

This adapter is for the huge cup holders in my 06 F150, to prevent my cans from falling over every time I turn a corner or hit a bump.

Goes in the rectangular slot beside the cup holders, secure with hot glue. ...Tested with 2015 Ford F150 supercab and 2021 Ford F350 supercrew, both with bench seats.

F150 2016 and up adapter for Nalgene 32oz water bottle. ... Taper was modeled from a Turvis cup as they fit snug but not overly tight. I have confirmed that it fits in all of the center console cup holders.

I was previously using a magnetic phone mount jammed into my coin holder in my F150. I found the design by muftrel and remixed it with the design from Coder-Tronic to make an adapter that is solid for different types of phone mounts. I'm sure you...

The tray is versatile and can be used with or without the charger, accommodating even larger phones like the Note 4, measuring up to 157mm x 85mm. A thoughtful cut-out allows users to securely attach their charging cable to either the charger or...

sculpture F150. ...Symbol (F) - MUSEUM SCULPTURE - TEMPLE PLACE 3d photo capture by nexus 6p.

Made a small clip that fits under the back seat on an F150 (2015 - 2020). Mine is a 2017 so made specifically to fit it. You can extend the Z-axis to whatever height works for your application, or have multiple prints for greater support. ... No...

I use this in my 2013 F150. I got sick of searching for my flashlight and used this to mount it to the rail. ...The flashlight it was designed for is: https://www.harborfreight.com/3700-lumen-ultra-bright-led-zoom-flashlight-57292.html It can be...

In my revised version, I relocated the cup holders to the outer edges and integrated three slots within the center console for cell phones, accommodating all Samsung Galaxy models as well as many iPhone variants comfortably. ...The final slot was...

This is a coaster for a cup holder in my truck. It is specifically for a 2017 F-150 because I am missing one. It is 77 mm in diameter and can probably be used in most other cars. ...I am printing it with TPU because it has a higher heat tolerance and is...

To address this issue, I designed a custom bottle holder that fits snugly into the air vent louvers, allowing cold air to circulate around the bottle and cool its contents. And yes, it works remarkably well - you might be astonished by the noticeable...

Center console phone cradle w/usb cable pass-through. Slide it into the track of the retractable door. ...The door holds it securely.

Center console phone cradle w/usb cable pass-through. Slide it into the track of the retractable door. The door holds it securely. ... If you like the design, please consider a tip: https://www.paypal.com/paypalme/thisrudager

Stainless Contigo travel mug rattles because the factory cup holder is hard at the bottom. Printed in TPU, the annoying rattle is gone. ...Fits 2013 F150 center console.

This cup holder adapter 1999 Ford F150 and other models. Water bottles, soda cans, etc. keep falling over when turning. So, I made this adapter to fill the space between the OEM holder and the drink. ... This solved the problem

... at a thickness of 0.111" as measured. ... Support kept as close to the vent to reduce the moment off the phone. Twistlock design was reversed from the official one. ... Fusion 360 design included if you wanted to change the interior dimensions.