phantom assassin 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Able to hold 1 stack of cards and 2 columns of hexes. --4-2-17-- Added player card 2.2, a little bit smaller on the separator pieces that come off the model, should be easier to fit in the box. --4-2-17-- Removed older hex and cards .stls and...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

-This current model is built under the assumption that most people will be using this with old tablets (or phones) that they would have thrown away otherwise, so taking a tablet (or phone) off of the top slider isn’t a smooth and seamless experience...

Also, I am considering some re-design of the right motor plate that currently interferes with the model fan duct. That would recover a bed Y-dimension back to 220. So, after all the print area will be 210x220mm... Parts to print: all parts at last...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

The design uses 12 '10mm x 3mm' (the magnets are actually closer to 9.95mm x 2.67mm).This is a spin-off from my earlier light-pull magnetic door catch: https://www.printables.com/model/209370-magnetic-low-profile-floating-head-quiet-door-catc , but...

If using liquid electrical tape, allow it to cure before continuing. Gluing Use a small amount of hot glue to attach the diffuser to the LED mount. Using To use, simply attach a 9v battery and insert the LED mount into the base, ensuring that the...

No special settings except for the optional color change.I suggest setting also the infill and supports angles to 35 degrees so it matches the angle of the parts.If you also want to print the letters on the cover you can use the MMU2 (or equivalent...

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...

Ok, so i designed another one because the existing models didn't satisfy me. I also made another design myself previously, but i was still not happy. The reason is that i dont know how all the pumps are designed. - Why do some pumps have...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

 Foam card (if you're not already familiar with it) is a material used in the art world and in crafting or modelling situations, a layer of foam is sandwiched between 2 layers of card, the resulting material is incredibly strong and is generally...

...Thank you! Change Log:25AUG2022 — Added model and print files of a 3-point version of the modified MINI-minda-holder for using the SPA with Sparkyman987's Fan Spacer Mod.11NOV2023 — Added .step file of the SPA for MINI/MINI+; added remix description.

UPDATE: 20.04.2022adapterplate (new design) for model C Hello, we would like to introduce you to our stealthburner conversion mod. At this time it works only with the klipper Firmware. The use with “Marlin” is planned later and will be...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

The assembly is not complicated, for each configuration I put exploded photos, pay attention to the insertion of the brass threads, (there are 2 models you need both), and to the direction of insertion, those placed in the attachment of the guides,...

Since the build volume on the Prusas is relatively limited i decided to maximize the footprint of the stand for stability. As for the height, the 2 piece construction while theoretically takes more time to print, there is no need for support for the...

IntroductionThis model provides an effective, low-cost teleprompter for livestreaming and recording. Using a Raspberry Pi and Pi Camera (the cheap, non-HQ one provides great full-HD video in this application), your phone to display your script or...

They aren't really required - they just provide some more protection. In addition to the printed parts, you will need the following: 1) 1/4-20 threaded rod, 3" length 2) 2 1/4-20 nuts 3) 2 M6-1.0 hex bolts 16mm length 4) 2 M6-1.0 hex bolts 30mm...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

We are modelling the *BELT* tooth here, not the tooth on the pulley. Increasing the number will *decrease* the pulley tooth size. Increasing the tooth width will also scale proportionately the tooth depth, to maintain the shape of the tooth, and...

rice or sand.Glue if the press fits are not tight enough Testing tolerancesStart by printing the models press_tolerance_test and rotation_tolerance_test from the folder Common parts.Press fit toleranceUse the press fit test to decide which press...

You may have to do some light cleanup, but the fit of the parts should be snug enough to hand press together with no wobble. IOMarms STL- These arms are taken directly from the original wood designs and are generally sized for an IOM, but are not for...

Or rather, it's a scale model of what that house looked like fifteen or twenty years ago. The wrecked version is closer to how it looks now that it's been abandoned for the better part of two decades. The tweakers have had a field day with this...

The design is a complete rework of my older oscillating fan model.It uses a common 130 size brushed hobby motor and incorporates an 18650 battery in its base for completely portable operation. Compared to the older design, the new version has...

It deviates a bit of what I usually call an "sci-fi astronomical object", because it's an in-spacecraft transport vehicle. I made this model available in 4 scales. I left the model in "halves" that I consider the best way to print it, of course, with...

Model says 119mm, which would be close.???---------------------------------------------------------------------------------------------------------Printed Parts: Base:___________________Placeholder____________________This is the base of the...

I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). Material: ABS, 3mm thick Nozzle: arcol.hu hotend v4.1.1, 0.35mm diameter Printer: DIY...