phanteks enthoo primo 3d models

-------------------------------------------------------------------------------------------------------------------------- I mostly work with the MPCNC-Primo with the Makita milling machine. To switch to the Trag knife is quite time-consuming to...

Motor and pipe mounts to allow you to use the [Tape Measure Trick](https://forum.v1engineering.com/t/better-than-a-cable-chain/6805) on the MPCNC Primo J-25.4mm (parts with no size suffix) and MPCNC Primo C-23.5mm. If you use the C-23.5 parts...

Print out the following parts for the Tool: 3 x Core_Clamp_F_Primo_V1.STL (from Primo standard components) 1 x Primo_CoreAdjust_Stabilizer_center 2 x Simple_Stabilizer_Core_clamps 2 x Drag_Chain_mounts_for_CoreAdjust (normal and mirror) This Tool...

Print out the following parts for the Tool: 3 x Core_Clamp_F_Primo_V1.STL (from Primo standard components) 1 x Primo_CoreAdjust_Stabilizer_center 2 x Simple_Stabilizer_Core_clamps 2 x Drag_Chain_mounts_for_CoreAdjust (normal and mirror) This Tool...

A set of cable chain brackets for the MPCNC Primo. Includes a remix of DJPicasso's cable saver and motor mount bracket. Each was modified to work with the other brackets added to the collection. only the X and Y brackets need supports. ...all models...

A set of cable chain brackets for the MPCNC Primo. Includes a remix of DJPicasso's cable saver and motor mount bracket. Each was modified to work with the other brackets added to the collection. only the X and Y brackets need supports. ...all models...

This is a mod for the MPCNC Primo version. With this Z-Max-Endstop you don't have to remove to remove the Z-axis. You have to replace the upper and lower toolplate and one "Core_Z_Clamp" (1 = left, 2 = right). ... The "Frame" is not realy needed but...

This is a mod for the MPCNC Primo version. With this Z-Max-Endstop you don't have to remove to remove the Z-axis. You have to replace the upper and lower toolplate and one "Core_Z_Clamp" (1 = left, 2 = right). ... The "Frame" is not realy needed...

These accessories contain the following parts: * **Frame corner for Alu profil 30x30mm** (to be used with the PRIMO corner bottom). The Primo corner bottom can be mounted on top of the frame corner (see images). * **XY-Drag-Chain-Mounts for Alu...

Some of the parts like the rail-drag-mounts, motor mounts and cable protection you can use also for a "standard" construction of the MPCNC Primo ... but I will publish another accessory set for the standard version, too. ...Print Settings Printer Brand:...

In addition to the my other accessories I have created a version for the standard PRIMO - even if you see the alu frame on the fotos. These accessories contain the following parts: *Drag-Chain-Mounts for 25mm pipes They can be used for drag chain...

In addition to the my other accessories I have created a version for the standard PRIMO - even if you see the alu frame on the fotos. These accessories contain the following parts: * **Drag-Chain-Mounts** for 25mm pipes They can be used for...

Through the [V1 Engineering Forum](https://forum.v1engineering.com/t/primo-style-belt-tensioners-for-the-lowrider2/19417/11) I had found some awesome "endcap + belt tensioners" by pilotkip, however, I also wanted the "Primo" CNC style method of...

Passend für: - Juwel Primo 60 - AniOne Aquarium Starter Kit 60 (von Fressnapf) Wenn man keinen Futter-Ring hat oder auch keine Lust hat immer zu versuchen diesen durch die Luke zu treffen, dann ist das hier die richtige und einfachste Lösung. Hiermit...

I finally upgraded my LowRider 2 MPCNC from wooden side rails to the Superstrut metal rails I have had laying here for the longest time.Through the V1 Engineering Forum I had found some awesome "endcap + belt tensioners" by pilotkip, however, I also...

Linear, AXII and UXII Canopy to allow mounting a Caddx Ratel or a Runcam Eagle Micro on the Gnarly Primo Frame. Camera angle is about 35°. Design to work with the 3" version but seem working with the original 2.5". I upload two versions. One...

The Canopy now allows mounting a Caddx Ratel or a Runcam Eagle Micro on the Gnarly Primo Frame with an adjustable camera angle of approximately 35°. Designed to be compatible with both the 3" version and the original 2.5", two versions of the canopy...

AS the stock 2.5" HDD and SSD Brackets are pretty expensive and also not very nice to look at, I decided to make these invisible mount brackets. Instead of using the side screws, it uses the bottom screw holes that are available on any 2.5" drive...

Anyone who purchased these strips knows that the included mounts/adhesive are poo. these are at least a little more stable when doing a long straight or bent run. the included mounts seem to leave some room for improving a straight line because...

This is my first 3D design ever, I picked up a Ender 3v2 just so I can make custom mounts and brackets for my SSUPD Meshlicious. I designed this because I had already purchased this pump lying around thinking it would fit in a dual radiator custom...

Their current reactions are already intense, to say the least.

It's designed for the 25mm (F) & 25,4mm(J) tubing and 30mm angle aluminum. ...I just use zip ties to hold it on, but you can also use a bolt.

I've seen a few wire chain attachments for the mpcnc that attach to the bearings and I didn't want to undo the bolts so I made a version that clips onto the motors. I also modified the truck clamps to have a little extension where you can bolt on...

Hey everyone this is a dust shoe that I modified from Nick Ellson's original design. He designed most of this and I simply modified it so it would fit my dust hose. My dust hose is the one from the Rigid Car Accessory kit from Home Depot. It is...

This battery holder accommodates GNB and RDQ 2S 450mAh battery packs, but the standard issue version can be somewhat restrictive for the largest batteries it was designed to fit. ... A revised configuration known as the "Toilet Tank Version" has been...

Same parts as klotzi18. I've just separated and oriented them to the bed. As a note for the long vertical tube, it will not fit on at least a Prusa MK3S. I had to cut it in half and print two of the bottom portions. Still have not assembled it...

First approach - works as intended :)

Info added here if needed.

This is a MPCNC Router Mount for a Ridgid R2400 Router.

I modified these covers to use a chain guide for the wires and also reduced its size to fit my Stepper motors. ... You can use this chain: https://www.thingiverse.com/thing:1824144