phanteks enthoo evolv atx 3d models

Mounting an Antec TruePower New XP 650W power supply unit (PSU) on a standard ATX case requires some care to avoid damaging both components. The mounting process is relatively straightforward, but it can be somewhat tricky if you are not familiar...

I decided I didn't want all those extra wires from my ATX power supply just hanging around, especially when it came to my 3D printer, so I created an end cap that attaches directly to the ATX power supply using its existing screw holes. Inside,...

This wall-mounted fixture supports a conventional ATX power supply. Its design was adapted from moczys' work to enable installation with the PSU's rear panel positioned downwards, held firmly in place by three 6-32 screws. ...Meanwhile, this wall-mount...

Secure the Power Supply ATX Unit: A Solid Foundation for Structural Support. ...Its robust design features a distinctive L-shape, providing stability through the use of two key anchor points: a screw on the left vertical side and one at the bottom...

I designed custom left and right-handed mounts for my ATX power supply unit (PSU), as I found several off-the-shelf options that failed to fit properly. ...Before installing, double-check the screw centers to guarantee a secure and precise fit tailored...

A custom-designed module features the ATX PSU-sized backplate with a Neutrik powerCON mount, engineered for secure DC power connection via a 2.1 x 5.5 mm socket. ...Measuring 150mm by 86mm in size, this plate boasts four strategically placed M4 nut...

Standard standoffs allow for easy mounting of motherboards on a variety of platforms, including ATX, mATX, and others. By elevating the motherboard off the ground, these standoffs prevent electrical shorts from occurring. ...They are typically secured...

... system that Garrett typically offers. ...It eliminates the need to stretch the bungy cord over the handle, and instead allows you to simply clip it around the top stem of the ATX. ...A convenient clip then enables easy attachment of the shoulder strap.

Ergonomic switch mount with integrated LED housing, engineered specifically to fit snugly into the wire exit hole of an ATX power supply unit. Designed for seamless integration, this mounting solution pairs perfectly with a 6mm switch and a 3mm LED...

Mount your standard ATX power supply onto a platform using this easy-to-assemble bracket; print two pieces then fasten them to the deck with four M4 x 20mm screws each. ...Secure the corners on the short edges with M3 x 60mm screw and nut for stability.

Just a simple ATX motherboard standoff. It raises motherboard about 2.3cm. Print it with the infill at 25%, and at the top section make it 100%. I recommend using Brim. ... If you have any suggestions please write them in the comments.

An ATX motherboard featuring precise geometry is offered, complete with IO panel, PCI, and GPU cut-outs and fixations. ...The motherboard's PCB Geometry aligns with the specifications provided in this link:...

A straightforward setup for an ATX power supply unit. Conceals all excess wires while still enabling airflow and maintaining coolness. ... **Double-check to flip the back plate over before printing, as its underside features a considerable overhang** ...

You're working with a straightforward SFX-ATX Adapter Plate. Possibly you'll need to fine-tune the holes for your intended application. Be cautious, as an extra grounding wire may be necessary between your power supply and case! ... Print Settings...

Replace the basic foot for your desktop ATX tower case with a new one. To achieve a smoother finish, preventing snagging on flooring or carpet, carefully place this part in an electric drill equipped with a 1/2" chuck. ...Use a file or sandpaper to...

A power supply cover I designed around a DELL ATX power supply. To eliminate support material, I decided to make the top portion foldable. Holes fit standard Banana plugs. ... The top is attached with aluminum tape, that part could use improvement.

I'm using an ATX power supply on my work desk for power for my projects. This is a mount to be installed under the desk to hold the power supply. ... It suits a power supply of 18.5 x 14cm x 14cm.

The design provides a safer electric system by incorporating an ATX power supply, allowing users to independently wire the heated bed and nozzle using two mosfets. Although this particular ATX choice is somewhat excessive, it will facilitate future...

Final Edition of ATX Board Released. Down and Top Case Now with Corrected Steps. Just Printed at Speed of 40mm/S - or Less Depending on Filament Used. Layer Height Set to 0.2mm for Optimal Results. ...Infill Density Now at 15/25% for Enhanced...

In an attempt to enhance my RepRap, I am currently designing an ATX PSU adapter to simplify power supply. ...I seek feedback to improve its functionality, aiming to utilize this innovation in my upcoming RepRap build and minimize the hassle of power...

I created this ATX Case because I have a Motherboard Asus P5G41T-M, and I run virtualization servers, and I wanted a personalized case that meets the exact dimensions of an ATX board. The case can be used with motherboards in both ATX and Mini ATX...

You'll Need to Drill Out the Female Connector Holes by Hand Yourself for Those Specific Pins Standard atx+4 pin connectors are a necessity here. Make sure You Have a Quality 3D Printer at Your Disposal Before Getting Started. ... ...

I designed a box for my ATX power bench supply. ... I took example from the DIY Bench power supply post from Rui Gaspar: https://www.creativesolutions.pt/diy-bench-power-supply/ But I had to redesign a box in order to fit all my needs WARNING :...

This is a modified version of the original design to accommodate an ATX power supply unit. For further information, please refer to the original thing on Thingiverse (https://www.thingiverse.com/thing:2748195). ...Alternatively, you can also print this...

Cableprotection solutions are a must-have for anyone upgrading to an ATX-PSU. The last thing you want is cables getting damaged or short-circuited during the process, causing costly repairs or even a fire hazard. ...With cable protection, you can rest...

I created a power supply for some radios and a Raspberry Pi from an old ATX power supply. There's four USB ports @ 5 V with 5 A breakers and four Anderson Powerpole connections @ 12 V with 10 A breakers. ...The breakers are from Amazon.

My ATX motherboard cable was a little too short, so I made this spacer to push the PSU further into the case. ... The thickness is 25mm, because this was the difference between PSU screws, and the fan screws I used for mounting this.

A 300-watt ATX power supply for computers is an efficient energy source for your system, ensuring stable and reliable performance while meeting the demands of your hardware components. ...This powerful PSU delivers clean and continuous electricity to...

I created this scale model of the Giant ATX 2, a medium-sized bike, using SolidWorks 2020. Given that I already own one of these bikes, I decided to make the most of my quarantine time by building it from scratch. ...Although the dimensions aren't exact...

This creator made a straightforward housing for their König CMP-PSUP450W/S ATX power supply unit, fashioning it from 5mm MDF. Two holes were included - one for a power switch and another for cable access. ...The finished product is used with the...