peq 15 mounting 3d models

So I made this to install slim Noctua fans (15 mm).Two versions are included:Pin_Screw.stl replaces the stock pins - use those to install stock grills with the screws shipped with the case; those will allow for about 5 mm more clearance than the...

I built a gaming table topper using series 15 extruded aluminum following the parts list and method from this video.https://www.youtube.com/watch?v=etzGon_lGlwI wanted more roll-in mounts for other things but I didn't need the full aluminum ones nor...

I made this in conjunction with my airsoft Peq battery box. I borrowed from Ohman74's IMF K Airsoft G36 Handguard, and his G36C "Spuhr R22"-like rail. Props to him. I only heavily modified his designs to make a more MG36 rail that I can run a battery...

... The PEQ box I got for it didn't fit, so I decided to make my own instead. ...I printed it out of polycarbonate, which is flexible enough to put the cover on and off, but I'm not sure about PLA.

Wooden shelves support decorative platters.

Support connecteur SUB-D 15 mâle Mounting bracket DB15

This is an extension to allow the Double Bell PEQ battery box to fit a 105mm length lipo battery on an airsoft gun. ...The pins are made from @3mm diameter bamboo barbeque skewer sections.

If you prefer not having them, don't print them - otherwise, print and glue them on (note that the covers fit both sides, so either way can be the front or back, so if you don't like the PEQ add-ons, print two of the normal cover/lid). I...

With this mounting adapter the wheelbase can be mounted at a 15° tilt for a more comfortable use of the wheel. Designed for Playseat Evolution, but can also be used to mount the wheelbase onto a table. Mounting holes at the outside are 165mm x...

I've long been searching for a peq box winch that would perfectly fit my 11.1 battery, but most models I came across were either too small or simply a basic box design. After gaining extensive experience with Fusion360, I decided to take matters...

Human: 15 Creality Ender 5 Mounting Bigtree 1.4 SKR Note this mounting positions the ports against the Control Box side. You will have to cut holes in the Control Box if you want physical access to the ports. This is a plate that allows for USB, SD...

This is a deep remix or peq model from user "paulodrugos" on thingiverse (https://www.thingiverse.com/thing:2098338) I always wanted a peq box winch will fit my 11.1 battery - most models were just too small or just simple boxes. After gaining...

Internal dimensions: 194mm x 20.3mm x 20.3mm PEQ/Battery Expansion designed for the new ASG CZ Scorpion AEG. Link to Compensator: https://www.prusaprinters.org/prints/35236 Link to Magazine Plate (mag pull): https://www.prusaprinters.org/prints/35235...

PEQ/Battery Expansion designed for the new ASG CZ Scorpion AEG. This custom expansion is specifically tailored to enhance your airsoft experience with the popular ASG model. ... To complete your customized setup, check out these additional components: ...

This is a mount to assemble three HC SR04 sensors at 15° to each other. It has three holes to assemble vertically or horizontally. They can be assembled towards the centre or towards the outside (concave or convex), two or more mounts can be joined,...

The first, included here, is a small clip to hold my spare Polymer AR-15 magazines. Any magazine with a bottom will work. If the Colt 20 rd metal clips are used, some type of magazine pull would need to be used to enlarge the base diameter to get...

... +/-40 degrees works well enough to turn the light on and off. Center of the servo is at 60 degrees. Dimensions: 120mm x 52.5mm x 16.6mm For a similar switch mount for a standard switch plate, see here: https://www.thingiverse.com/thing:1156995

The sensor boasts a mounting height range of 10' to 20' above ground, and provides up to 15' by 15' coverage when mounted at 16'. It is made from non-sparking aluminum, with a glass window for motion detection, and can be wall-mounted via an integral...

This high-quality detector can be mounted at heights ranging from 10' to 20', providing 15' x 15' coverage when mounted at 16'. Its non-sparking aluminum construction with a glass window for motion detection, vertical adjustment of -90° to +30° after...

This explosion proof motion detector can be mounted at heights between 10 to 20 feet above the ground, providing up to a 15 by 15-foot coverage area when installed at 16 feet. The unit is constructed with non-sparking aluminum and has a glass window...

https://www.larsonelectronics.com/product/144579/400w-explosion-proof-motion-sensor-20-to-25-mounting-height-15-x-15-area-coverage-timerThe Larson Electronics EXP-MS-N4X-AT-HV Explosion Proof Motion Sensor is approved for Class I, Divisions 1 & 2...

The one major difference between the AN-PEQ-5 and the larger AN-PEQ-2, is the AN-PEQ-5 lacks the IR illuminator/target designator which is only visible through night vision devices. ... This feature is primarily used to aid with aiming while using...

Customized version of https://www.thingiverse.com/thing:108865 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=108865

High-Resolution Peq-2A Red Dot Sight Installs seamlessly onto any Picatinny rail system

Airsoft players repair a file, designed specifically for airsoft. ...The updated version enhances gameplay.

The human body is a complex and intricate machine that requires regular maintenance to function at its best. By eating a balanced diet, exercising regularly, and getting enough sleep, humans can keep their bodies in top condition. ...This involves...

Small gear with 16 teeth.

I surveyed the area and there were no pre-fabricated boxes available, so I created one from scratch. It's not the most polished design, but it can accommodate a 2S 2200 mAh battery comfortably, making it ideal for users who opt for smaller cells. If...

I've modified the original file found at https://www.thingiverse.com/thing:2098338 to fit on a Picatinny rail by adjusting the attachment slightly. ...Everything else works smoothly.

<p>The front is fixed with one M3x15 screw and nut. ...(the front also have another two screws just for alignment), the fixation in the picatinny rail is made with a M3x30 screw and nut.</p><p>Print with suport (touching buildplate).</p>