penny fidget spinners 3d models
26301 3d models found related to penny fidget spinners.thingiverse
Another Mod... ...You can use 4 or 5 pennies stacked for weight.. ...I prefer 4 as it leaves pennies inset just a little.
thingiverse
This is a Remix from Procupine's Penny Fidget Spinner. The problem with Procupine's STLs 1 & 2 is that they are not scaled correctly. They needed to be scaled 1001% !!! My files are ready for print to fit standard 608 skateboard bearings (22mm...
thingiverse
Someone asked if I could make a Captured PENNY Fidget Spinner to go along withmy Captured Nickle and Captured Quarter spinners. So, here it is. There is a file for ABS or PLA. Use your favorite button or one of mine, either ABS or PLA. I used...
thingiverse
The best fidget spinner, giving the most weight, will be one that uses 1979 or earlier pennies since they weigh 3.24 grams each, compared to 2.35 grams for the newer pennies. The next best would be one that has 4 pennies in each arm. Since the older...
prusaprinters
I put a tiny dab of SuperLube Synthetic Grease on each BB before inserting the finger pads into the bearing. American pennies are the same diameter, so they can be used as well. The best fidget spinner, giving the most weight, will be one that uses...
thingiverse
This fidget spinner uses 8 pennies for mass! you need to pause the print and place the pennies, creating a smooth seamless spinner. enjoy! ... design/timelapse/assembly video: https://youtu.be/mhfFn41Vu3o Print at your own risk, embedding metal...
myminifactory
Fidget spinner using US pennies as weights, in several different sizes. There are very small ridges that hold the bearings and pennies in place, designed to fit the chamfer on Bones Reds bearings* (they have a smaller chamfer than the VXB bearings*...
cults3d
Fidget spinner using US pennies as weights, in several different sizes. There are very small ridges that hold the bearings and pennies in place, designed to fit the chamfer on Bones Reds bearings* (they have a smaller chamfer than the VXB bearings*...
thingiverse
https://www.reddit.com/r/3Drequests/comments/5y5btw/request_penny_spinner_stl_version/
thingiverse
Fidget spinner using US pennies as weights, in several different sizes. There are very small ridges that hold the bearings and pennies in place, designed to fit the chamfer on [Bones Reds bearings*](http://amzn.to/2qDGWNM) (they have a smaller...
thingiverse
Yet another fidget spinner. This on based on the suggestions and process from Joel, AKA the "3D Printing Nerd" as found here: https://www.youtube.com/watch?v=EgOuvOLiwAM The fit is very snug so the pennies won't fall out. I had to use a bit of force...
thingiverse
I used Fusion 360 with my son to design this fidget spinner. Fits 609 bearings (0.866" diameter) and pennies (0.75" diameter). I find 3 per penny hole works well, and weighing them to balance them out is helpful. I also have caps, which I'll post...
thingiverse
Steps after printed: (1) press penny's into either sides of the spinner to add counter weight. (2) put bearing into center hole. (3) put the caps on either side of the bearing. ...(4) Have Fun, And SPIN!!!
thingiverse
one i designed on tinkercad takes 5 penny's each hole a drop of super glue on the corners will hold the penny's in
thingiverse
Put 3 penny's in each hole and glue them in then put a bearing into the hole i the middle (The hole is 22.2 mm) idk what kind of bearing it is
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2108154 Instructions Using the following options: radius = 2 rays = 5 taperedRays = yes extra = 0 numWeights = 1 whichWeight = penny
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2108154 Instructions Using the following options: whichWeight = penny extra = 10 numWeights = 1 taperedRays = yes rays = 6 radius = 2
pinshape
It's two spinners, unevenly weighted, so you can spin them in opposite directions. Simply flip them in opposite directions and keep shaking your hand to keep them in motion. Plus they fold up like a switch-blade when you're done. ... For assembly...
thingiverse
The Duo Spinner fits 3 pennies per slot. The Tri Spinner fits 3 pennies per slot. the larger spinner fits 4 in 3 of the slots and 3 in the other slots. ... Stop by my profile to check out some of my other designs :)...
thingiverse
Tip: Use a gram scale or a balance for your sets of pennies to make sure they are very close to the same weight in each arm to get proper balance. Or only use all pennies from the same year or something. ... The metal composition has changes many times...
thingiverse
Print to a tight press fit for 24 pre-1982 US pennies (3.11 grams each). This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/j6dtnYvzrCb
thingiverse
Customized version of http://www.thingiverse.com/thing:2360208 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2360208
thingiverse
Great design by walter, just tweaked it a bit, all press fit and smooth. Added the finger pad from 2ROBOTGUY. ...Best designed pad I could find.
thingiverse
Customized version of https://www.thingiverse.com/thing:2108154 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2108154
thingiverse
Customized version of http://www.thingiverse.com/thing:2108154 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2108154
thingiverse
Customized version of http://www.thingiverse.com/thing:2108154 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2108154
thingiverse
Customized version of http://www.thingiverse.com/thing:2108154 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2108154
thingiverse
I also have another penny weighted fidget spinner I designed and please go check that out! ( Sorry I don't have a picture yet of the final product. I am printing it right now.) How I Designed This I first saw 2ROBOTGUY's fidget spinner, and I thought...