pelican kayak cup holder 3d models

... on bottom to fit into the surface of a cut out hole. ... You could use this for a kayak, such as I did, or a table top, or any other flat surface with a cut out hole. The bottom piece threads on to tighten and secure the cup holder into place. ...

Manufacturers design a cup holder that fits most kayaks, plus other items like tables or chairs. This clamp-on attachment is versatile. We offer two versions of the cup holder: one for smaller objects such as cans and glass bottles, and another...

this is a 2 piece cut in cup holder for kayak or plastic boat the bottom would need to be epoxy to the bottom the top will have a lip on it this was designed to hold beer coke Pepsi or water bottles i printed mine on abs and have 2 installed on my...

Track-mounted cup holder for kayaks. Printed with PLA. Fits plastic bottles and cans perfectly. It can use a 1/4-20 bolt or a yak attack bolt to attach to your kayak. All part links may not be the best place to get the parts, Many can be found at...

Seems to fit standard kayak rails but could easily be mounted to other devices. Designed to fit single can without additional insulation. I will make a version 2 soon with a larger diameter to account for this potential issue. Modeled in...

Pelican kayak scupper plug specifically for the 100xp angler. Hole to run paracord. Print out of tpu. ... Have been river tested with no issues.

This is a substitute lid designed to fit Ascend brand kayak cup holders, particularly the FS10 model. I have successfully printed test samples of every detail and they all match perfectly with my 3D printer's capabilities. ...I am now preparing for a...

The same hatch is used on most of Pelican's SOT kayaks, and depending on hull depth, this insert should fit seamlessly in all of them. The bottom attaches to the walls using six M3*5mm machine screws. **UPDATE 12/05/2021**: I've added a v2 version...

Designed this gopro mount to replace the "Pelican" Oval badge on my Boost 100. Use the two exising holes on the end and can drill a center hole for best stability. ...I used rivets to secure it down

My Seastream Angler 120 didn't come with a cup holder so I designed this one and should fit any of the feelfree kayaks that use the unitrack. It is designed to use a tapered 10-32 screw and hex nut. The nut will need to be glued into the track...

By following these steps, you'll have a secure cupholder for your kayak, even if it only came with three rod holders like mine did. **UPDATE 6/15/2020:** To accommodate my Pelican Enforcer 120x, I've added an 18° spacer to ensure the cupholder sits...

Rudder mount solution designed specifically for Pelican Argo 100x Kayak, but also compatible with many other Pelican sit-in kayaks. To install: simply remove the rear carry handle and then insert a 1/4-20 bolt paired with a large diameter washer...

Replacement scupper plug for the Pelican SOLO childrens kayak. Designed to be printed with TPU. ... It is a tight enough fit that it takes a bit of work to get out with your fingers but it definitely wont pop out on its own.

The pod works for all Hobie Mirage Drive, Pelican Hydrive, and Vibe X-Drive kayaks. It is designed to be used with a watersnaker t24 or t18 trolling motor. It has a hole for a locking rod to be mounted, and a slot for a standard size 12in ruler or...

Rack Mount, Pelican Kayak, 100x series This fits the Pelican 100x series & a std, 1-1/4 x 7/8" Load bar, Designed to be low profile, vertical mount. I haven't had any wind noise on mine yet, but someone will probably prove me wrong. I'd suggest using...

Printed with 100%infil, modeled to accept a yeti koozie. ... requires 5 10-32x1/4" counter sunk screws

The Pelican Vortex 80 features a compact, flat surface with curved slots that extend outward at right angles. Measuring approximately three-quarters of an inch in width, these slots are narrower than standard paddle clips can accommodate. ...Instead,...

The new configuration includes a revised mounting design that optimizes the placement of components to enhance overall performance and stability.

An insert for a Pelican 1020 that allows you to store 150 rounds of .22 in the factory plastic. ...I've only tried it on SK 22 ammo boxes so it may not fit others.

kayak handle holder

Watch/GPS holder for kayak to attach with suction cups purchased here :...

A versatile paddle holder boasting an innovative design seamlessly accommodates kayaks of all standard sizes. ...BEWARE: installation requires drilling a precise hole in the kayak's upper section to securely fasten the holder via its top-mounted screw.

Bottle holder for captain's chair for kayak. Very handy to have it. ...You can swing it around.

This innovative number board holder is specifically crafted for kayaks and canoes. ...Its design draws inspiration from classic Kirton Kayaks and Marsport number boards, ensuring a seamless integration with your watercraft.

This design features a straightforward kayak paddle holder, ideal for printing and attaching to the side of your vessel for maximum stability.

I crafted a base for the holder that fits snugly in the kayak's bottom and bonded the two parts together with some strong glue. ...Kudos to Alaska3D for creating the original beer holder design, which can be found at...

... ...I crafted a custom base that fits snugly into the kayak's bottom, then secured the two parts together using a strong adhesive.\r\n\r\nSpecial thanks to Alaska3D for creating the original holder design!\r\nhttps://www.thingiverse.com/thing:2295833

... while its adjustable straps provide a customized fit for paddles of various sizes. Perfect for kayakers who want to keep their paddles safely stowed away when not in use, this holder is a must-have addition to any kayak storage system.

Pelican keepsake

A pelican