pegboard filament spool holder 3d models

A spool holder designed to be used with a pegboard (1/4" holes, 1" apart). ...Print the holder and two pins and you're good to go!

Print a spool holder that fits snugly into a pegboard with pre-drilled 1/4-inch holes spaced one inch apart. ...Then, print two matching pins, and you'll be ready to roll!

Based on the link http://www.thingiverse.com/thing:397649, key changes were made to accommodate monoprice-sold filament spools, primarily lengthening them. ...Printed on a FlashForge Creator Pro using ABS plastic with raft and support structures at...

I've crafted a straightforward 2-piece spool holder for pegboard use. Simply insert both cylindrical components into opposite sides of your spool so that the smaller cylinder fits snugly within the larger one, then hang the entire assembly on your...

Speaking of which, filament spools I'm using are almost universally 60mm thick by 195mm in diameter (across the circle.) Pretty much all filament brands are fine, tho I've been using Sunlu PLA without complaint. More important than the filament brand...

This is a pegboard mounted filament spool holder. I designed the bracket with 4x3 (pegs) for maximum structural integrity, and added extra sets of mounting holes so that you can double or triple up arms on each bracket, or use them for accessories...

... was far too narrow for my spools. ... I created this which is a direct swap in part for the original back piece, it is 75mm wide which fits my polymaker, hatchbox and Atomic filament with room to spare. ... Uses the same M3 12mm screws as the original

In this package, you'll find the following things: 1) Spool holder for the IKEA Pegboard. This thing came in two pieces; you should glue them together. This way it saves you a lot of support material and print time. 2) The PTFE Tube holder for on...

In this package, you will find the following things: 1) Spool holder for the IKEA Pegboard. This thing came in two pieces that should be glued together. This way, it saves a lot of support material and print time. 2) The PTFE Tube holder for on the...

Spool holder meant to mount to an Ikea-brand pegboard (no, they're not the same as US standard pegboards, for some reason). I haven't long-term tested it to make sure it won't sag overtime, but I'm hopeful. ...The design is meant to be simple and...

I designed this pegboard mounted bracket for holding a spool of filament. My new garage workspace needs a clear bench so I got the side-mounted spool up onto the wall. This is designed for 1" (25.4mm) center-to-center pegboard. The filament spool...

I designed this pegboard bracket for holding one or more spools of filament.This is designed for 1" (25.4mm) center-to-center pegboard. The filament spool spins on a piece of PVC tube that's approximately 2" (50mm) outside diameter and rests into the...

I created this innovative pegboard mounted bracket specifically designed to hold a spool of filament in place. My new garage workspace demands a clutter-free bench, so I built the side-mounted spool up onto the wall for optimal use. This design is...

As of this release, the arms that go into the pegboard along with the filament holder extensions are complete and work with HATCHBOX PLA spools. This thing can be customized to fit your needs, and I've included a .blender file of all the current...

The Pegboard Filament Spool Holder (https://www.thingiverse.com/thing:1471847) is one of the most ingenious creations since sliced bread, but it has a significant flaw: The existing pegboard hooks are excessively thin and tend to pop out of the...

Other pegboard filament spool holders exist, but I sought one that is simple and uses minimal materials, printing with very few supports. This design is primarily intended for a hatchbox spool, yet can be used for many other spools less than 3.5...

I remade a pegboard tape holder design that I really admired to accommodate filament spools. The revised design still fits neatly on a standard 1x2 board. To get the best fit, I suggest printing one bracket as a mirror image of the other, since it's...

You will need to print two hanger blocks, two outside spacers, two washers and one spacer to make a spool holder wide enough for a (MakerFarm) 1Kg filament spool. The holder mounts on two long pegboard hooks, 4" apart. ... Category: 3D Printer...

To get my filament spools off of the floor, I made a pegboard hook to support them.

I really love the solid spool holder but needed to cut down on print time and filament used. Hexagons are the solution!Fits standard 1" x 1" pegboard. I used 10% density tree supports (touching the bed) for the top pegs. ...I printed it with ABS, but...

Attach 3 standard Radio Shack wire spools (1" inner diameter) on a pegboard using this holder; assemble two parts together or fasten Part B with zip ties directly onto the pegboard.

Holds 3 standard Radio Shack wire spools (1" inner diameter) onto a pegboard. Instructions Put the two parts together then clip onto your pegboard. Alternatively, you can forget about Part A and just hold Part B to the pegboard with zip ties....

This spool holder offers numerous advantages: - It's made from affordable parts - Fast printing times make it a convenient option - The design is fairly sturdy and can withstand regular use - Low friction on filament spools ensures smooth and...

Simple, and somewhat inelegant remix of the filament holder by Olafpeter for use with 1/4" hole pegboard.

Two versions of the holder are required - a short one for spools up to 60mm in diameter, and a long version for spools up to 100mm in diameter. Space between the holders is exactly 1", ideal for pegboards with 1/4" holes. The included pegboard plug...

For use on a 1-inch center-to-center pegboard, these spool dowels are perfectly designed to keep all your filament spools organized and within easy reach. Measuring 3.2 inches in length, they come in two different sizes to accommodate various types...

The two-piece screw that attaches to the spool comes directly from [jterranella](https://www.thingiverse.com/jterranella)'s [Pegboard Universal Spool Holder](https://www.thingiverse.com/thing:1689099) with no modifications made at all. ... I highly...

I love these versatile change spool holders (https://www.thingiverse.com/thing:1241566), but after installing pegboard, I realized a way to mount them was essential. This is my speedy design. I'm using a 5/16" x 4 1/2" bolt as the rod and two zip...

I wanted a universal spool holder that mounted on my pegboard, but I wasn't a fan of most of the ones on Thingiverse. So, I modified an existing pegboard mount to hold my favorite spool holder. This spool holder runs on bearings and is universal to...