pebbles from flintstone 3d models

This is a feature a few people have asked for, to make it operate a little more like the reels they are used to from Jobo and PatersonAdded a push-feed lock on inline, so the reel doesn't unnecessarily twist when using the push-feed loading method. I...

I redesigned the pulleys to have a reasonable overhang, but am currently using the ones from my earlier mod, so cannot guarantee the new ones will work fine; they will likely require some adjustment. The SCAD file utilizes features present in the...

These were either created by remixing other models or by creating from measurements of existing parts. I brought these previously published designs together here as an example of a project that could be done with students. Print Settings Printer...

You suddenly realize the wireless charging isn't doing it for you, and you MUST arrive at your target destination at 100% battery then just pull out the USB cable from its cozy little nook and plug it in. -- IS IT WATERPROOF?? -- No its not,...

...The range of x and y values for my plot are from -2 to 2, and the plot is of the Julia Set function z=z^2+c with c=-0.18-0.48I over 30 iterations. I produced the values in c when I requested Wolfram Alpha give two random integers between -100 and 0.

Object description:This LCD knob can be rotated in a wide range of angles from all sides.A video how it works you can find here: CV Joint Knob Video. But please note, that the fit of the main part on the LCD was a bit wobbly with this prototype. It's...

DescriptionThis design features remixes I made from community designs. These remixes are available for free at Printables. The sale of this product only applies to my original designs. Thanks to the following designers: Thank you to JAAANIK for...

You might be able to do without glue (or to use glue without screws), but a belt-and-suspenders approach seems best, given the fact that the two screw points are both on one side of the board, so gravity will tend to pull the board away from its...

They are too small to pop off a flex plate easily, however, using a needle-nose pliers, they can be pulled off individually from the build plate. This is easily done by grabbing one of the legs and gently twisting. The special-o2-bar.stl has...

Links: Orbiter Extruder: https://www.thingiverse.com/thing:4725897 (I just bought the ready-to-go Orbiter version from Aliexpress) Fan duct: any regular Predator fan duct would do as long as it stays clear enough of the Hotend. I used Sakman's 4020...

Well, I was thinking out ways to prevent myself from indulging two different vices: Number one (Often in connection with no2): eating some candy, and then some more, and even more, and a whole lot of it. And number two: to by default start...

To install linear bearings into plastic parts: * Slide the bearings on rod * Heat up the plastic part with heat gun for 5-10 seconds (do not melt) * Slide in bearings from both sides * If binding, remove and try again Similarly for X carriage,...

I made mine from both PET G and ABS which I normally don't require the use of a brim or a raft. I did need to use support for the magnet recesses, but I found that no support also worked well for me. The magnets will be glued in place. The problem:...

Their purpose is to prevent the tray from sliding when placed on top of the lid, both when in play and when storing multiple stacked trays in between sessions. Optionally, one each of the small and large card dividers. They are intended to separate...

I had remixed a design from @morganlowe, but assembly of it was too complex. So I searched around and found a one by @designsbydave. I downloaded it and added my own backplate I have designed, smoothing out the iffy details and adding some extra...

 Make sure to check on the water level periodically and refill as necessary.Future Work: Since the basin is supposed to hold water, I may try PLA acetone smoothing to help make the print more water-tight.Please like it if you do and leave any...

To talk on discord I used to use the integrated microphone of my headphones (sony sbh60), but now I use linux and there is no way to change from high quality audio codec to that of headphones with microphone (you can choose, usually it is done...

Design requirement needs:Have a large curved surface for the filament to run.Smooth running with minimal friction.InexpensivePrint without supportUse readily available partsAesthetically pleasing Ingredients:PLA7 g - 2.34 m - 1 hr 6 min for the...

What this means is the servo motor controller does not react when there are stepper pulse input from the RAMPS 1.4 board in between this 1 millisecond, the servo motor controller react to this stepper pulse input only when the 1 millisecond timer is...

The height is measured from the top edge of the box. 2. Enter the depth of the hook. This would be, for example, the width of your armrest. 3. Enter the height of the hook's attachment. 4. Set the type of hook. "Separate" is intended for...

I had to exaggerate the diameter of the cannons to make them less brittle.It can be used with a small pin and holder from here. If you want to use it, add the peg ("t65_x_wing_peg.stl") as a part before slicing. Works with both the print-in-place...

This is my version of the Autobot Matrix of Leadership, from the 1986 animated movie. I've found several good versions to print online, but they all print in a single color. This model is split into individual components so that each color can be...

Did you order an M48 Barlow lens from Aliexpress? Did they ship you an M42 lens and then stop answering emails? Never fear, this is an M42 to M48 lens adapter. This works with my Amscope microscope.</p> <h3>Print instructions</h3><p>Print in PLA with...

Yet this low level detail presentation in contrast sharply diverges from its lower resolution representation, the model known as Rock_9_Lod_1 that possesses merely 3159 polygons paired to a vertex count of 1582. Consequently, Rock_10 boasts...

(one where I can afford an iPhone 7!) How I Designed This I googled the design parameters for an exponential horn profile (https://mysite.du.edu/~jcalvert/tech/speak.htm) and built a blended surface from cross-sections laid out in a spiral. Putting...

Nik's Dremel CNC is an incredible innovation.\r\nWhile building it, I made several modifications to get the most out of it!\r\nAll components are fully compatible with the original Dremel CNC.\r\n\r\n### TPU Foot\r\n- Print at least 4 of them with...

on a modified Anet A8: https://youtu.be/r3VDSf2LWgQ Longer Video from the ABS print with small tips: https://youtu.be/Eq14PsOnR8U Inspired by the legendary "Makers Muse" Torture Egg: https://www.youtube.com/watch?v=_IHmfQviSoE More will come if you...

I designed this model so the unused limit switch from my CR-10 Mini can be easily repurposed as a filament runout sensor. The limit switch is commonly found in Creality CR-10 and Ender 3 printers and consists of an SPDT switch mounted on a small PCB...

The important things to know about this print are the following :It worksIt can be improvedFilling and painting is needed for best resultAs can be seen from the referenced remix, I made a full size print of the Maltese Falcon some time ago. That...

Here's how to use it: 1.) Print all the parts, a low profile rim and a wheel lock from the original F1 STLs. 2.) Cut two 6cm pieces of M3 threaded rod and a smaller one to mount the wheel. 3.) Close the holes in the rim with something, for example a...