pcie bracket 3d models

There are the things that inspired my design: Filament Spool SyStem (https://www.thingiverse.com/thing:2769588) by Jimbo70 (this was my main inspiration and is fantastic) Custimizable TUSH bracket (sized for Rubbermaid 21 cup filament storage)...

ratherbe_flyin has made a bracket for the BLTouch mount which he tells me works perfectly at the following link: https://www.thingiverse.com/thing:3780708 The parts still use the original locking part but the Base units will only be compatible with...

Added a new design (Shark main support V2 - no festos.stl) that doesn't require festos (uses couplers and festo-less brackets). Instead it uses rivnuts to hold the ptfe tube. This means that your PTFE tube won't wear out over time as the festos chew...

Distance between the centre of the leadscrew and the motor bracket is 3mm on the ones i used to design this. If the ones you have differ to this the design will need modifying to work. Print all the 3d printed parts, I did everything in PLA but then...

Just print multiple braces, and move the brace to the desired spot.Ease of use: Just place the guide in the bracket, hang the spool on the guide, and off you go. If there happens to be another guide right next to the one you want to use, you needn't...

So after spending some time looking at similar RX7 engines for sale on Ebay, I designed coils, a bracket to hold them, sparkplugs, and wire boots to simulate an ignition system. I also designed an oil filler tube and cap, to help fill the gap. The...

The probe dock was modified to fit the botton lug of the X gantry and extended a bit to match up with the probe block when it's attached to the toolhead.The probe retainer was redesigned to make it long enough to grab the probe and the backside of...

An example of usage of the Dual Axis V bracket could be to provide the reference pivot in a 3D printer fitted with a 1P Z motion system. <b>The claims for the Dual Axis V-Pivot are as follows.</b> i) There will be no clearance between the...

Bottom part of the PCB would slide into lips on the sides of the housing while top is secured with a screw on one side using a small bracket.Printability improvementsMost of the parts have been adjusted for better printability by removing overhangs,...

Hello to everyone who has chosen a Prusa MK3S Clone. The parts that I have put together differ a little from the original MK3S, but this compensates for the few weaknesses. I bought the MK3S from AliExpress and had to find out that the included parts...

-edit- you can combine this design with flexible pivoting through-puts of https://www.thingiverse.com/thing:4902775-EDIT- 31-10-2021 I designed support brackets for the 4mm PTFE tubes to support the filament exiting the dox. Choose variant "b" for...

Motor brackets for 4-hole M3 mounting with a diameter of 25mm can be used as feet or 7.5mm square aluminium tubes can be inserted. When mounting the camera on a rostrum towards the front, a comfortable viewing angle should be provided. Pay...

I may upload a few different shim sizes if I can get some feedback on how much of a gap there is between the motor and the top of the carriage, but for now if you want/need to shim the gap, you can either print a tiny square/rectangular shim in...

There are the things that inspired my design: Filament Spool SyStem by Jimbo70 (this was my main inspiration and is fantastic) Custimizable TUSH bracket (sized for Rubbermaid 21 cup filament storage) by x0pherl TUSH2 - Sliding Positions by...

Those designs were a great starting point for me.I made adjustments to the relay body, relay cap and curved bracket to make them closer to what I think is accurate.The rest was modeled by me using screengrabs of the A-Car Flux Capacitor when it was...

I have not seen any side effect in rigidity terms but you may want to attach some additional corner brackets if concerned about the rigidity of the frame overall. 4.With XY joiners there is no perfect print orientation due to the stress by the...

I've included a mount for the drag chain that bolts to the guide wheel mount on the end of the gantry too, and the mounting brackets are hopefully universal enough for other chains to bolt to without too many issues. This is a WIP, which honestly...

This is a servo hinge setup for use with MIPRESIDENT's Iron Man Mark III helmet (http://www.thingiverse.com/thing:260152). You can see my final build here: http://www.thingiverse.com/make:286759 And a video of it in use here:...

If you want to retrofit the blower fan and this duct on an older printer that does not have the mounting bracket, you can print my clone of it.   Using Just as with the stock duct, a limitation is that it only blows in one direction, meaning that...

So after spending some time looking at similar RX7 engines for sale on Ebay, I designed coils, a bracket to hold them, sparkplugs, and wire boots to simulate an ignition system. I also designed an oil filler tube and cap, to help fill the gap. ...

The LED light fixture assembly can be removed by releasing the hand knob and sliding the light and mounting bracket off of the center support while the legs can be collapsed, aiding in deployment, storage and transport. The lamp can be easily...

Because I was going to have to cut one of these stereo lenses in two, I had the idea to provide a holder/clamp/bracket that would hold a maximum of 2 lenses in front of the Cam 3 with the big advantage that absolutely no changes would be needed to...

For the mod I got rid of the belt tensioners, since we already have a pair, adjusted belt positions, fitted an Orbiter v1.5 and an optical x-endstop and fixed some design flaws of the original EVA design. EDIT-24.12.2020 HAD EVERYTHING PRINTED AND...

The printout consists of 8 parts to be printed separately and assembled : The body (which fits on the chassis very easily) The rear chassis The rear wheel axle The two rear brackets to lock the rear wheel axle The front part of the vehicle The...

- Update 2/14/2020 Updated the Y axis rod holders to be a little stronger around the screws and fixed the upper right corner bracket hole positions. - Update 2/22/2020 Updated the X motor mount to correct some clearances for the endstop switch. ...

Do the same for the dragon mount, the blower fan mount, the dial holder and the ribbon cable bracket, for these inserts you can use the Qidi metal scraper to ensure they are flat against the surface. In total 9 brass inserts will be mounted in...

If you purchased and assembled the kit version of your Prusa 3D printer, then this upgrade will be a rebuild of the X gantry, repositioning the Z axis mounts, and padding the Y axis mounts and motor bracket. The extruder/hotend wire loom must be...

Do the same for the dragon mount, the blower fan mount, the dial holder and the ribbon cable bracket, for these inserts you can use the Qidi metal scraper to ensure they are flat against the surface. In total 9 brass inserts will be mounted in...

Do the same for the dragon mount, the blower fan mount, the dial holder and the ribbon cable bracket, for these inserts you can use the Qidi metal scraper to ensure they are flat against the surface. In total 9 brass inserts will be mounted in...

If you don’t use the full printing hight, you can just assemble the pulleys right under the top leadscrew brackets and connect them with the belt. I prefer to flip the top leadscrew brackets, pull the leadscrews a few mm out of the motor coupler and...