pci express fan 3d models
167484 3d models found related to pci express fan.
thingiverse
... overheating issues with my Adaptec RAID card and I need to give it a break. ...The culprit is the blocked airflow caused by the PCIe slot, which is restricting the fan's ability to circulate air. ...It's time for a lighter load on this component.
prusaprinters
92mm Fan mount that fits onto the PCI-E area with magnets.Used to cool SSDs sloted in with PCI-E to U.2 adapters, or all other PCI-E cards.Fan used: Noctua NF-A9x14Magnets used: Neodymium 18x8x4mmFor a fan grill, use thing:2802474 from mightynozzle,...
thingiverse
92mm Fan mount that fits onto the PCI-E area with magnets. Used to cool SSDs sloted in with PCI-E to U.2 adapters, or all other PCI-E cards. Fan used: Noctua NF-A9x14 Magnets used: Neodymium 18x8x4mm For a fan grill, use thing:2802474 from...
thingiverse
I personally prefer to use mine as an intake fan by attaching a filter over its back and directing fresh air towards the front (hard drive bay) and back (PCI slot duct). This cools nearby expansion cards efficiently while also bringing in cool air...
prusaprinters
This is a mount to allow a standard 120mm fan to be mounted over the PCI/PCIe slots to blow air down on to the top of expansion cards. I use this to cool a server RAID card and NIC that have a heat-sink, but no built in fan. ...The mount is designed to...
thingiverse
This is a custom-made mount designed to secure a standard 120mm fan above PCI/PCIe slots, channeling air directly onto expansion cards. I utilize this mount to cool a server RAID card and network interface controller with heat sinks but no built-in...
thingiverse
For my mount you need 4 PCI-E Slots free and put one mount on the bottom and another rail on the bottom (it's also possible with 3 slots and one mount, but i cant say how the air pressure of the fans will affect the mount. ...I used 4 rails for the...
thingiverse
PCI fan bracket for 92mm fan. Fully printable without supports. ...
thingiverse
I remix this file to put 120mm's fans under my rtx 3070 zotac because they fans are not very efficent. ...
thingiverse
... My PC Today Said No One Ever --------------------- I designed this for cooling the toasty LSI HBA adapter in my home server. ... The compact version saves a bit of filament. The Full Frame version provides extra support to the fan. ...
thingiverse
Nuclear-enhanced upgrade, reimagined for high-performance PCIe x4 cards. A customized version of the original design, precision-tailored to provide a secure and precise fit for your cutting-edge hardware. ...By subtly narrowing the slot aperture, this...
thingiverse
80mm Fan holder - PCI slots version for Silverstone GD11
thingiverse
PCI slot bracket for 92mm fan. ... Fully printable without using supports.
thingiverse
Remove two PCI Slot Covers -> insert the fan mount bracket with installed fans -> screw the bracket to the case Plug the 4-Pin fan header into the mainboard. I used a Y-Splitter to power both fans from one mainboard fan header. **Software** I use...
thingiverse
Nobody use this anymore but if you need one you can use this one, it only need some support on the PCI screw hole and to attach the fan it use M3 Screws.
thingiverse
Designed to add an exhaust fan to the vertical PCI slot. Efficiently discharges the heat generated by the GPU. I designed this for the Fractal Define R6, but I think it could probably be used for other PC cases as well. #### Update 2022.03.30 ...
prusaprinters
So, i bought 3 60mm fans that fit in the little perforated space next to the PCI expansion slots, and made a bracket to mount them. ...This should bring in fresh (read - cool) air for the GPU that is then exhausted out the top. Has pockets for M3 nuts...
thingiverse
40mm is slightly bigger than two PCI slot width so if the lower slot is occupied, do check if you have some clearance as the fan will encroach very slightly into the next slot. If you want to do this, you'll probably know that a 12V fan is normally...
thingiverse
... so crafted one from scratch with SketchUp after eight trial runs to nail the dimensions and stability. ... Version 2 - polished the design, refined the surfaces, and corrected a brief PCI extension issue (my bad). ... Version 1 - initial prototype.
thingiverse
Air intake system for PC installed, consuming four valuable PCI slots. Its primary function is to cool the graphics processing unit within my computer enclosure. A makeshift air filter has been secured to its surface using adhesive, improving overall...
thingiverse
This was made to make a mount for a 120mm high pressure noctua fan to blow on the backplate of a 3090 graphics card. I dropped 2 40x40x20mm heatsinks I had into the void for the air to blow through. Flipping the fan to pull from the back and blow...
grabcad
A Solidworks 2017 SLDPRT and STEP model displays a Mini PCI Express card, with a thickness of 1mm. ...It features standard offset 52 x 8mm Pitch pins and the design was derived from Molex 67910-1002 PCB connector data sheets (included).
grabcad
This item is versatile as it works with 1X, 2X, 4X, 8X, and 16X configurations (both 1-16X and 16-16X are supported). ...It features a PCI-E circuit board adapter. ...The power connector utilizes a Sata 15 pin configuration.
prusaprinters
<p>I created this clip to hold in the male end of the riser cable sold at https://www.amazon.com/dp/B07Y46WTD1 as well as other similar listings.</p> <p>Part is pre-aligned to lie down on build plate, print without supports. Adjust horizontal...
thingiverse
I created this clip to hold in the male end of the riser cable sold at https://www.amazon.com/dp/B07Y46WTD1 as well as other similar listings. Part is pre-aligned to lie down on build plate, print without supports. Adjust horizontal expansion in...
thingiverse
I set out to install my video card vertically and keep a solid sound system intact. To accomplish this, I crafted a makeshift mount utilizing two existing screw holes on the case. Two slightly extended coarse computer screws, leftover from my build...