pcb standoff spacers 3d models

I recently needed some PCB standoff spacers for an Arduino project, so I created these simple customizable ones in OpenSCAD as a learning exercise to hone my skills. I now print a few whenever I need them because it's convenient. The source for this...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1360337 Instructions Using the following options: spacer_height = 0.5 mm spacer_count = one separation_factor = 1 point 55 times screw_size = 0 point 112

http://www.thingiverse.com/apps/customizer/run?thing_id=1360337 The source for this project is maintained on GitHub: https://github.com/mseminatore/mdsSpacer Instructions Using the following options: screw_size = 0.112 spacer_count = 4 spacer_height...

http://www.thingiverse.com/apps/customizer/run?thing_id=1360337 The source for this project is maintained on GitHub: https://github.com/mseminatore/mdsSpacer Instructions Using the following settings: separation_factor equals 1 point 25 screw_size...

Customized version of https://www.thingiverse.com/thing:1360337 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1360337

Customized version of https://www.thingiverse.com/thing:1360337 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1360337

Customized version of https://www.thingiverse.com/thing:1360337 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1360337

Models of a range of M3 male and female PCB spacers:5mm10mm15mm20mm

This model is meant to be as simple as possible to print and use and it's especially suited for using leftovers of your almost empty spools.every spacer comes with a 5mm and a 10mm version. ...There are spacers for M2, M2,5 and M3 screws.

This model is meant to be as simple as possible to print and use and it's especially suited for using leftovers of your almost empty spools.every spacer comes with a 5mm and a 10mm version. ...There are spacers for M2, M2,5 and M3 screws.

Standard M3 30mm standoff PCB spacer.- Inner diameter 3mm- Outer diameter 5.3mm- Height 30mm

Quickly remodeled the standoff by taking exact measurements of the one that I didn't break.Didn't print nicely on my Anycubic mega x, had to drill &amp; tap the center hole. ...But it still fits and does the job perfectly.</p>

Print in any plastic with at least two walls that are 30% infill. Single STL available for easy multiplication as needed. *Additional STL included for printers with poor calibration, featuring a wider ID. ...Print Settings Printer Brand: MakerBot ...

Spacer Stands Firm - PCB Mounting Options Expand with Sizes 9mm, 10mm, 15mm, 20mm, 25mm, 30mm, and 35mm.

Handy spacers designed to fit snugly over M3 standoffs with a diameter of 5 millimeters. ... 2.5mm 5mm 7.5mm 10mm

PCB standoffs accommodate 3mm holes and permit secure attachment using 1/2-inch double-sided tape for added stability.

... tape. ... A taller version of this design features a height of 10mm, replacing the original 1mm model. To ensure proper printing, it's likely necessary to rotate the PCB Standoff by 90 degrees. ...Additionally, no support is required for this design.

A standoff to mount a small electronic circuit board (PCB) on a mechanical carrier board, such as plywood. The standoff clips into a hole in the board. A screw goes through its top that keeps the PCB in place. If the screw is long enough to reach...

My brand new boiler control module was in a world of trouble, thanks to two shattered standoffs that held its vital PCB in place. My trusty 3D printer sprang into action! I designed these replacements from scratch, taking the original standoffs as a...

...Version 1 is a revolved sketch with the PCB at 12.7mm and it's 25m tall - sorry about the orientation! Version 2 is a loft with the PCB at 12.7mm and it's 24.7mm tall. ... If you print and use it before I get to, let me know how it turns out for you!

PCB Spacers (Height 6 and 15mm) for +/- 2,80 or 3mm diameter screws, compatible with a number 7 Flat Key.