pcb clip standoff

NEMA-17 1:4 step-up gearbox for remote direct drive
thingiverse

Clip upper carrier to lower carrier, fitting the shafts to their corresponding holes. After assembling the planetary gears, lubricate them well. # Installation 1. Press fit 4 M3 nuts into the extender bracket. 2. Attach the exender bracket...

MyRCCar Typical Pickup, 1/10 RC Car Body for MTC chassis, both versions
cults3d

he was reporting to the comunity all the problems or improvements he found and he created alternative/improved parts to solve some problems, like for example: - BotYoyo's Light weight roll cage for MyRCCar MTC - BotYoyo's Clip-On links for pickup...

N3o : Lack Drawer for prusa mk3s [for N30 Lack Enclosure]
prusaprinters

(stay tuned) On the right side of the lack instead there is the drawer that contains the USB transformer and the connections of the electrical contacts and a second drawer that contains 1 raspberry 2 modules of 4 relays and 2 esp8266 boards For now I...

My Customized Pattern Bracelet
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=401429 Instructions Using the following options: pattern_clip = 95 pattern_copies = 30 pattern_rotation = 180 inner_diameter = 60 height = 10 pattern =...

Tyre Truer MKIII for slot cars 1/32
prusaprinters

DC 6V-12V 6500RPM Large Torque JOHNSON 385 Motor Carbon Brush DC Motor for Tools - http://www.ebay.com/itm/262443105339?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT) 1 on-off switch to be press fitted into the slot of the main body (I...

Customizable Triple Letter Blocks Ambigram
cults3d

The letters E,F,I,J,P,T, and Z should also have supports, but they can be printed without if you don't mind clipping and sanding the messy first several layers of the unsupported areas where supports should be used. Of course, the letters on the...

Fiberoptic LED Hybrid Wall Clock (40cm) v6.1
prusaprinters

Other reasons are that steel doesn't care about heat, and it's lightproof Stripboard or custom PCB:I use a good quality white stripboard that was cut with metal cutting shears into a 53mm circle.Can't really tell you how exactly to make this, as...

(V1) For BIQU B1 - DIY Enclosure - Remix of Prusa's IKEA Lack Enclosure - with extra doors (opening on 3 sides)
prusaprinters

Those sheets are: Bottom-Corners.stl Door-Knob-(x3)-and-Cable-Clips-(x10).stl Top-Corners.stl Top-Extenders.stl Additional parts that are not ganged up on a sheet with others: BIQU-B1-ac-heater-wire-redirect-strain-relief-bracket.stl (The main reason...

(V1) For BIQU B1 - DIY Enclosure - Remix of Prusa's IKEA Lack Enclosure - with extra doors (opening on 3 sides)
thingiverse

Those sheets are: **Bottom-Corners.stl** **Door-Knob-(x3)-and-Cable-Clips-(x10).stl** **Top-Corners.stl** **Top-Extenders.stl** Additional parts that are not ganged up on a sheet with others:...

CR-10s Pro V1, CR-10s Pro V2 and CR-10 Max Maintenance, trouble shooting and upgrade guide
prusaprinters

Just read the installation and disassembly instructions of the 3D model.Filament guides https://www.printables.com/social/261164-caesar_1111/collections/159007 just pick the design you like from the collection, but it is important that you have...

Temperature Controlled LACK Enclosure With Motion Sensor LED Lights
prusaprinters

Input Current: 0,11 AVoltage: 12 VN/A • Molex 4-pin to 3-pin Fan Power Adapter Converter Cable1 x Molex cable to cut and connect fans to MH1210A temperature controllers.4-pin LP4 to 3-pin TX3 Fan Power Adapter Converter Cable.Simultaneous connection...

Mounting plate for 5.25" speakers in Stern pinball machines
prusaprinters

Too much and the connector will get too fat to fit into the housing. When inserting each connector, pay close attention both to its position and its orientation.On my machine, the speaker negative goes on the side of the connector with the clip, but...

Onewheel XR VnR Battery Pack (63v 16Ah Li-ion 20700 15S4P)
myminifactory

Then clip the BMS plate over one side of the battery cells so that the black wire reaches the negative 2x2 corner with ease.7. Cut some lengths of Nickel strip, 75mm and 30mm lengths, you'll need a few but cut them as you continue through the...

Ornithopter Dune 3D Printing Model | Assembly + Action
gambody

The 3D printing model’s chosen scale is 1:64 for the FFF/FDM version and 1:128 for the DLP/SLA version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 61 parts;- A printed model stands 368 mm tall, 456 mm wide, 560 mm deep (platform +...

Full Build Instructions for Slack Lack (Ender 3 / Ender 3 Pro) Plus Accessories
prusaprinters

In my case, I'm running up and down the sides of each leg, as well as along the top, except in the case of the front in which I only do theback of the leg. Attach each clip with finishing nails or wood screws; attach the LED strips as you go for...