pc4 m6 3d models

SImple Y for dual filament on single nozzle, less 3cm long, for pc4-m6.

Modified the end to have an M10 threading, for use with PC4-M10 fittings.

Titan Extruder Adaptor M10-PC4 Connector for Secure and Reliable Connectivity

PC4-01 Inner plug, for no problematic inserting filamentBuy me a coffee:https://ko-fi.com/jokereuc

This version of clip allows you to screw in a PC4 (Push to Connect) M10 PTFE fitting.

... version will have clean holes without the use of supports. ... RepBox PC4-M10 adapter with large hole https://www.thingiverse.com/thing:3939989 by Forfelet which is a remix of RepBox PC4-M10 adapter https://www.thingiverse.com/thing:3709863 by Brandito

Front PTFE Holder used with Splitter https://www.thingiverse.com/thing:4680412 Designed for PC4-M10, now it's possible to remove entirely the selector from MMU2S unit. ...

This is just a PC4-M10 Adapter for the top of the Prusa Mk3 extruder to allow a PTFE tube to be firmly affixed to it.

Numbered couplers for joining 4mm PTFE tubes using PC4-M10 pneumatic fittings. ...I use these to connect tubes from my dry boxes to my MMU2S buffer.</p>

I added a BSP 1/8 thread to the STL, so that you can screw a M10-PC4 ptfe coupler directly into it.

... fittings within a sealed dry box environment. ...Designed to accommodate manual insertion of a PC4-M10 fitting at its bottom, this guide addresses a common issue where standard guides lack the precise thread pattern required by these specific fittings.

... version will have clean holes without the use of supports. ... RepBox PC4-M10 adapter with large hole https://www.thingiverse.com/thing:3939989 by Forfelet which is a remix of RepBox PC4-M10 adapter https://www.thingiverse.com/thing:3709863 by Brandito

The Sensor Cover For Pc4-m10 Bowden Coupler is a protective case designed to shield the sensitive electronics of the PC4-M10 Bowden Coupler from dust, debris and other environmental hazards. This durable cover provides a snug fit around the coupler's...

This is a replacement lever tension arm for the Titan extruder clone to allow a PC4-M10 PTFE connector to be attached to allow the 3D Chameleon to feed the extruder.

Finally made a PC4-M10 adapter for push-through bowden fittings. ...I use it on the extruder drive, so I don't need that extra small piece of bowden tube.</p>

I don't have that "PTFE Tube Retainer", but I do have a lot of PC4-M10. ...Here is a version that takes just that (M10 0.5mm thread)

Just an edit of Neptune 796's Artillery Sidewinder Palette adapter to allow a PC4-M10 PTFE adapter to be used instead for the 3D Chameleon and the Prusa style MMU. ... It is recommended to print it with 100% infill.

Another remix for PC4 M10 pass through couplings. The slot is 4mm higher to geht the M10 thread fit. That needs a longer handle as well, the stl is also attached. Be careful when inserting the PC4 M10 coupling. The side walls are a bit thin and can...

Support free remix of the following, this version will have clean holes without the use of supports. RepBox PC4-M10 adapter with large hole https://www.thingiverse.com/thing:3939989 by Forfelet which is a remix of RepBox PC4-M10 adapter...

In this remix, you're free to utilize the PC4-01 pneumatic fittings. The PTFE tube flows directly into the middle of the merger. ...To complete this project, simply print the design twice - once normally and once as a mirrored duplicate.

An adapter for a PC4-M10 fitting with 0.9 pitch thread that attaches to the run-out sensor. I made it for my filament dry box setup. ... The clip is inspired by texelsaur's design and I removed some of the top for better clearance.

I bought this little set from Amazon, but you can use most any PC4-M10 - just check it out on the link here: https://www.amazon.com/gp/product/B07FPJHRTQ/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1 This is a brand-new design. ... Thanks for taking a...

### Voron M4 with PC4-01 Bowden Connectors This is a remix of the beautifully designed [Voron M4](https://vorondesign.com/voron_m4) extruder. Since the bowden collet in the original design is a little bit hard to source, I've adjusted the size of...

I had some spare PC4-M10 connectors that are through-bore like in the picture where the PTFE can pass all the way right through. Since the filament isn't getting stuck directly in the PTFE, I figured I could route the PTFE straight to the selector...

Modifications include: PC4-M10 Pneumatic Fitting Better cooling Improved filament loading (may cause issues with flexible filaments) Increased space around gears Space for M3 nut Edit 2018-11-27: This extruder demands a powerful stepper motor and...

This simple holder securely holds five PC4-M10 connectors with M10x0.90 threading, designed for easy installation on a shelf. To organize my workspace effectively, I needed a solution to manage the five tubes leading from the MMU2 unit and decided to...

Remixed from Ri3del's https://www.prusaprinters.org/prints/108198-reverse-bowden-clip which I made shorter to fit in my enclosure and added threads for a PC4-M10 fitting.Thanks to Ri3del for providing the .step file so I could make these changes for...

Hey makers,I still had exactly 5 PC4-M10 PTFE adapters and i wanted a long clip to integrate them into Michal Fanta's wonderful spool holder system. So I built in an M10 thread and minimized the holes from 4 to 3 mm so that the PTFE does not slip...

This coupler is designed to seamlessly integrate into a BMG dual drive extruder or clone, enabling users to leverage a pneumatic push-fitting Standard type PC4-M10 while allowing the Bowden tube to pass through the push fitting with ease. Two...

... through, instead aligning perfectly with the tube on the opposite end. Here are the PC4-M10 couplers I purchased: https://smile.amazon.com/dp/B078SRBDS7/ Here are the 3M Command Strips I use: Learn more at https://smile.amazon.com/dp/B0751RPC6Q/