pc4 m10 3d models

I Found myself impatiently waiting for my ptfe fittings to arrive so i designed a solution using TPU.It should fit nice and snug into the M10 threaded hole and the 4mm outer diameter ptfe should also be a snug fit.If you find that the fit is to loose...

Sensor Cover for PC4-M10 Bowden Coupler

My updated design for Bowden clamp for PC4-M6 and PC4-M10. ... I currently use old broken PC4-M10/6 without pneumatic part, in some cases i have added a whasher in order to hold the clamp. ...

Modified the end to have an M10 threading, for use with PC4-M10 fittings.

... I've managed to break the PC4-M6 fitting. ...Unfortunately, it's not holding onto the tube securely. Luckily, I have a spare PC4-M10 fitting lying around, which I'll be using as a makeshift adapter until I can source a replacement for the broken part.

A Custom Bowden Coupler Adapter for the PC4-M10 and PC4-M6 Straight Male Pneufit Remixed from Model Number 2208165, Created by Mightynozzle

... version will have clean holes without the use of supports. ... RepBox PC4-M10 adapter with large hole https://www.thingiverse.com/thing:3939989 by Forfelet which is a remix of RepBox PC4-M10 adapter https://www.thingiverse.com/thing:3709863 by Brandito

This is just a PC4-M10 Adapter for the top of the Prusa Mk3 extruder to allow a PTFE tube to be firmly affixed to it.

Front PTFE Holder used with Splitter https://www.thingiverse.com/thing:4680412 Designed for PC4-M10, now it's possible to remove entirely the selector from MMU2S unit. ...

Numbered couplers for joining 4mm PTFE tubes using PC4-M10 pneumatic fittings. ...I use these to connect tubes from my dry boxes to my MMU2S buffer.</p>

... version will have clean holes without the use of supports. ... RepBox PC4-M10 adapter with large hole https://www.thingiverse.com/thing:3939989 by Forfelet which is a remix of RepBox PC4-M10 adapter https://www.thingiverse.com/thing:3709863 by Brandito

... fittings within a sealed dry box environment. ...Designed to accommodate manual insertion of a PC4-M10 fitting at its bottom, this guide addresses a common issue where standard guides lack the precise thread pattern required by these specific fittings.

The Sensor Cover For Pc4-m10 Bowden Coupler is a protective case designed to shield the sensitive electronics of the PC4-M10 Bowden Coupler from dust, debris and other environmental hazards. This durable cover provides a snug fit around the coupler's...

I don't have that "PTFE Tube Retainer", but I do have a lot of PC4-M10. ...Here is a version that takes just that (M10 0.5mm thread)

Another remix for PC4 M10 pass through couplings. The slot is 4mm higher to geht the M10 thread fit. That needs a longer handle as well, the stl is also attached. Be careful when inserting the PC4 M10 coupling. The side walls are a bit thin and can...

Finally made a PC4-M10 adapter for push-through bowden fittings. ...I use it on the extruder drive, so I don't need that extra small piece of bowden tube.</p>

This is a replacement lever tension arm for the Titan extruder clone to allow a PC4-M10 PTFE connector to be attached to allow the 3D Chameleon to feed the extruder.

Just an edit of Neptune 796's Artillery Sidewinder Palette adapter to allow a PC4-M10 PTFE adapter to be used instead for the 3D Chameleon and the Prusa style MMU. ... It is recommended to print it with 100% infill.

Alle weiteren Teile bleiben Original. Aufbau: Die PC4-M6 Kuplungen passen nach lockern der Schrauben am MMU2-Hinteren-PTFE-Schlauchhalter ohne Änderung. Die ausgdruckten Adapter mit den 5 M3x10 Schrauben auf dem S-Puffer verschrauben (in den...

Support free remix of the following, this version will have clean holes without the use of supports. RepBox PC4-M10 adapter with large hole https://www.thingiverse.com/thing:3939989 by Forfelet which is a remix of RepBox PC4-M10 adapter...

An adapter for a PC4-M10 fitting with 0.9 pitch thread that attaches to the run-out sensor. I made it for my filament dry box setup. ... The clip is inspired by texelsaur's design and I removed some of the top for better clearance.

To connect PC4-M10 to PC4-M6, an easy extension of PTFE tubing to the Prusa enclosure is necessary for MMU2. This allowed me to easily join the spool varying length PTFE tubing to MMU2 tubing. PC4-M6 Connectors can be purchased on Amazon at...

I bought this little set from Amazon, but you can use most any PC4-M10 - just check it out on the link here: https://www.amazon.com/gp/product/B07FPJHRTQ/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1 This is a brand-new design. ... Thanks for taking a...

Hey makers,I still had exactly 5 PC4-M10 PTFE adapters and i wanted a long clip to integrate them into Michal Fanta's wonderful spool holder system. So I built in an M10 thread and minimized the holes from 4 to 3 mm so that the PTFE does not slip...

Modifications include: PC4-M10 Pneumatic Fitting Better cooling Improved filament loading (may cause issues with flexible filaments) Increased space around gears Space for M3 nut Edit 2018-11-27: This extruder demands a powerful stepper motor and...

This simple holder securely holds five PC4-M10 connectors with M10x0.90 threading, designed for easy installation on a shelf. To organize my workspace effectively, I needed a solution to manage the five tubes leading from the MMU2 unit and decided to...

... through, instead aligning perfectly with the tube on the opposite end. Here are the PC4-M10 couplers I purchased: https://smile.amazon.com/dp/B078SRBDS7/ Here are the 3M Command Strips I use: Learn more at https://smile.amazon.com/dp/B0751RPC6Q/

This coupler is designed to seamlessly integrate into a BMG dual drive extruder or clone, enabling users to leverage a pneumatic push-fitting Standard type PC4-M10 while allowing the Bowden tube to pass through the push fitting with ease. Two...

Remixed from Ri3del's https://www.prusaprinters.org/prints/108198-reverse-bowden-clip which I made shorter to fit in my enclosure and added threads for a PC4-M10 fitting.Thanks to Ri3del for providing the .step file so I could make these changes for...

Hey makers,I still had exactly 5 PC4-M10 PTFE adapters and i wanted a long clip to integrate them into Michal Fanta's wonderful spool holder system. So I built in an M10 thread and minimized the holes from 4 to 3 mm so that the PTFE does not slip...