pc reservoir mount 3d models
365249 3d models found related to pc reservoir mount.thingiverse
Mount for a 60mm tube reservoir. ... The mounting holes are 50mm apart and are for M4 screws to thread into.
thingiverse
Simple support structure for a horizontally mounted water reservoir. ...Pushed the res up by 15 degree so as to keep the air-bubble away from the pump.
prusaprinters
Simple support structure for a horizontally mounted water reservoir. ...Pushed the res up by 15 degree so as to keep the air-bubble away from the pump.</p><ul><li>No Supports</li><li>0.3 resolution</li><li>5% infill</li><li>Prusament Gray PLA</li></ul>
thingiverse
Here is the stand that I used to mount my EK reservoir horizontally, as shown in the picture.
thingiverse
... of 50mm. ... It is designed to be used with a countersunk M4x16mm screw. It is meant to be mounted in a M4 thread, in my case on the side of the 5,25 Inch Bay of my Lian Li PC A70 Case. Of course, it can be used in other PC cases. Have fun! ...
thingiverse
This is a NEW version of my PC Watercooling reservoir holder with a diameter of 50mm. https://www.thingiverse.com/thing:3900098 Easy to use, snap on mechanism! I printed it in PETG, but PLA should do the same. ...
cults3d
... same screws that many radiators use to attach to their fans. You cannot attach it with PC fan screws. It is threaded for standard G1/4" fittings. You may want to run a lower flow setup to avoid bubbles; this is not a very large volume reservoir.
thingiverse
If you want to print the top, base, and matching reservoir then use parts V4 Top, V2 Base, and print the provided reservoir.*** This is a combination of a few designs but with a different package; hence the clear used PC reservoir. Use/store this...
prusaprinters
used for holding a water-cooling reservoir
grabcad
This product features a dual-reservoir mount measuring 50mm, similar to Singularity Computers' prototype design.
thingiverse
Print best in TPU, -Slide the RGB Connector-Cable through the hole -Cut LED-Strip to correct length -Solder -Put Ring over the Reservoir -Wire it -Light it up -Enjoy :)
thingiverse
This is my Clutch reservoir mount I designed to hold a small motorcycle reservoir for my manual swapped SVX. My first revision failed (snapped the side off) so this is my revised version. I have yet to test it but will very soon. EDIT: it worked...
thingiverse
This is a radiator mount for the Heatkiller Tube Reservoir. Print settings: 20% infill minimum, 35%+ recommended. Two left and two right parts are needed. In total, 4x M3x20 bolts, 4x M3x8 bolts, and 4 M3 nuts are needed. ...
prusaprinters
The wall mount stand for the 'Coolant Overflow Reservoir Tank fit for Mitsubishi Montero Dodge Ram 50 Raider' to be used e.g. for the boat engine.</p> <p>Better print ABS or similar stiff heat resistance material. ...Adding a safety belt around tank...
thingiverse
The wall mount stand for the 'Coolant Overflow Reservoir Tank fit for Mitsubishi Montero Dodge Ram 50 Raider' to be used e.g. for the boat engine. Better print ABS or similar stiff heat resistance material. ...Adding a safety belt around tank with...
prusaprinters
I present a simple reservoir mount, it was created with an 120mm fan in mind, using printer friendly parts. ...The ring styled mount is designed for a 60mm tube.I've used simple black PETG from Eryone.printed at- 0.15mm height- 15% infill and 3 wallsThe...
thingiverse
This is a one-inch (25mm) ball mount for brake or clutch reservoirs. My motorcycle uses M4 bolts to secure the hydraulic fluid covers to the reservoir. Remove the cover retention bolts, and replace them with bolts 6mm longer. You may want to first...
thingiverse
Just a holder for the E3D Titan Aqua water reservoir to attach it to 2020 extrusion. The print on the photos was a rush job in PETG but it does the job. The holes are 5.5mm in diameter and accomodate M5 and below. Even clamping surfaces on the...
thingiverse
A simple holder for mounting a relay to the shock body on a DRZ400 motorcycle.
thingiverse
drop in insert to stop vortexes and bubbles in water cooling pumps for PC's heres a link to the specific model i designed it for https://www.amazon.com/gp/product/B01GZPW7VS/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
grabcad
This text describes a concept for mounting the Aquacomputer Aqualis reservoir using CNC 5mm aluminium, with holes spaced to fit 120mm fan positions on the case. The installation process involves unscrewing the top cap and sliding it into place within...
thingiverse
It will only fit a Heatkiller Reservoir, the upper mount point will only attach if you have the multiport top.. The extra machine screws that are attached to the bracket and the case are for peace of mind. The Bracket itself is designed so that...
thingiverse
I wanted to make a wall mounted PC and needed to find a way to mount the PC components on the wood. ...So I made the mounts.
grabcad
This mount allows you to add an additional fan to a PC when normal mounting options are not available.
thingiverse
This is wall mount for tablet pc Print Settings Rafts: No Supports: Yes Resolution: 0.3 Infill: 50