pbs mods 3d models

... and buffer full. (had to use 5-pin automotive relay instead of 4-pin Remixed from: https://www.thingiverse.com/thing:4257637 https://www.thingiverse.com/thing:4145271 Tom-Penns collator mods (no longer on thingiverse) Photos are coming soon... ...:)

... At the top, a convenient 1-inch or 25.4 mm segment allows users to grasp wrenches securely as they screw the mod into place on the lab faucets. Print Settings Rafts: Yes Supports: Yes Resolution: A precise infill layer resolution of 0.1 mm.

I'm not responsible for any damage that might occour in combination with these mods!** My own designs: * simple rear wing/spoiler - should be printed in TPU! * front shock protector/brace - M3x25 screws needed - the stock screws will fit, but...

This front sight piece mod and bolts(arrows) fly straight and the thicker design of the front piece increases the power of your crossbow slightly. For use with the cheap toothpick crossbows that you can find on Wish, etc. The new front sight...

... need to be drilled to fit M3 grub screws) 5: drive shaft couplings for no binding I am using the gears modified by:Eight20 @ https://www.thingiverse.com/thing:1937515 Printed at 100% infill. More mods to come as testing is still in the process

Here is the start of my BLV Cube mods. I will be slowly adding additional remixes of the original parts. Parts: * Z motor mount These motor mounts have room for using Rubber O-rings. For those who wish to use solid couplers or integrated lead...

Here is the shopping cart for all my mods: - [Banggood Z-Axis Fixture](https://www.banggood.com/de/Aluminum-Z-axis-Lead-Screw-Z-Rod-Bearing-Holder-with-Bearing-Housing-for-Creality-3D-CR-10-Enedr-3Pro-3D-Printer-p-1577566.html?rmmds=myorder) -...

Two Threes Sapphire Pro Mods Kit =========================== The following parts are available: 5010_Volcano_Fan - It's a shroud for a 5010 blower to be used with a volcano hotend, installed on the original coldend. It has a sensor mount for an NPN...

Source files can be found on GitHub at [https://github.com/brandonhill/Eachine-Racer-130-mods](https://github.com/brandonhill/Eachine-Racer-130-mods). I made this modification because I initially had a problem with the stock flight controller, so I...

Files: - large spacer: to be glued to the receiver - small spacer: can be used to space the spacer in the arm - mod bullet: the bullet that fits the cylinder If you enjoy my prints or remixes please consider becoming a Patron! Early STLs, images of...

I also redesigned the back plate to allow attaching wrist rests and have included the current ones I'm using.  In the pictures you can see the fully modded Sofle, I cut the new backplate out of  frosted 5mm acrylic as I think it looks nicer then the...

All of my mods for my mpcnc primo F-25mm. STLs are oriented for printing. Everything prints without supports, except a few parts. Please refer to the description below and/or the included gcode. XY EndstopsHardware needed:2x M3x5x6 heatset insert, or...

WL Toys V950 helicopter mods as per YT video - https://www.youtube.com/watch?v=jDN8mQqpB10 NB. All these will need fettling. I've had these on three V950s and they've all been slightly different. 1. Brace across chassis mounts. Pretty easy. 2. ...

Here are my mods to improve the quality of the frame Diatone #37. In this mode, you'll find: -ARM SPACER: there are two different arm spacers available. With this spacer, you can put the ESC between the two plates and choose from 7mm or 5mm...

Here are a few mods for the BNB SX extruder. 1) Revised lower clamp with cable support - This is designed to prevent binding when the extruder is on the right-hand side. The normal Bear/BNBSX extruder has its cable support connected beneath the...

Hi guys, These are some bits and pieces to mod the Injora Buggy Bouncer. Overview of 3D parts here: https://youtu.be/MvJFd2ElRg0 Bouncer Build Guide here: https://www.youtube.com/watch?v=KtU9XnC91Hw XR247 Axles Guide here: ...

Hi guys, These are some bits and pieces to mod the Injora Buggy Bouncer. Overview of 3D parts here: https://youtu.be/MvJFd2ElRg0 Bouncer Build Guide here: https://www.youtube.com/watch?v=KtU9XnC91Hw XR247 Axles Guide here: ...

Mods for an Ashford table loom The sectional beam dividers allow loading a warp with sectional tools like AVL's warping wheel or a spool rack. In addition to the dividers, you will need 4 dowels that fit the holes. I drilled mine for 5/16" dowels. I...

You will need to re-tune your extrusion steps after this mod. Print instructionsCategory: 3D Printer Parts Print Settings Rafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 50% Notes: All parts should print without support in the...

This pack contains a precision-crafted sound suppressor 3D model that accurately replicates the PBS-1 Assault Rifle Silencer 5.45's sleek design. All modeling details are painstakingly adhered to the original specifications. The model boasts 1516...

Encountered problems with barrel alignment, resulting in BBs consistently striking the front cap.

For full screen, go to YouTube.

These hands may be more Lego like and thus they may look better. Your choice. ... This is from https://www.tinkercad.com/things/ba08CfRsl6h-the-hand by swagdadfrombaghdad.

A push button toggle switch can be easily operated by switching it on and off. ...It features a mounting hole with a diameter of 12 millimeters, ensuring secure installation.

These hands might resemble Lego pieces, making them appear more appealing. It's ultimately up to you. ...The design can be found at www.tinkercad.com/things/ba08CfRsl6h-the-hand, courtesy of swagdadfrombaghdad.

Das Werkzeug der Bandsäge ist recht klein und man muss es bestimmt dauernd suchen, wenn man nicht gleich einen Halter dafür an die Säge baut. ... Es gibt zwar Löcher zum anschrauben, ich habe aber doppelseitiges Klebeband verwendet.

Das Original 2mm Insert wirkt sehr schwach. Ich habe eines mit 5mm Dicke gedruckt. Die Löcher habe ich weggelassen, weil man nachträglich Bohren könnte und weil sie bei 5mm wahrscheinlich eh verstopfen würden. ... Hier habe ich noch eine Version...

By Tóth Béla, a teacher, in collaboration with creator Tóth Valentin, this project was developed at the Beszédes József MMIK located in Magyarkanizsa, Serbia. ...Utilizing Solid Edge ST5 as their primary CAD software, they brought their design to life.

Customized version of https://www.thingiverse.com/thing:1038261 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1038261