patio table umbrella 3d models

Glass Patio Table Umbrella Gromet

Patio Table Umbrella Pole Spacer

Bought an outdoor patio set with no umbrella, so we bought an umbrella and had to make a grommet so the umbrella would not rub on the table.

Designed this to replace the sleeve that fits in the hole of a patio table for an umbrella. ... Fits a 65mm hole in table and has a 44mm hole for umbrella.

Bfayer's insert design is awesome, but not quite the right size for my table/umbrella, so I scaled the original to fit my table, and then expanded the center hole to fit my (metal) umbrella shaft. ... Tinkercad model is public - help yourself:...

Plastic umbrella ring for a patio table. This was used to replace the insert that cracked over time in my patio table, and is modelled as a replica of the original. it is a tight fit - to insert place 2 of the prongs into the table insert and use a...

This little insert protects glass a patio table from the umbrella rod rattling around. Some improvements over the original design for strength and fit. Fits great on mine but you should verify the size of your table first. ...Mine measured 2.005" dia x...

This is an insert to support the umbrella for our patio table. These support both the umbrella in the holder on the ground as well as aligns the umbrella at the table hole. This is a simple design, but I have provided .STP files so you can modify for...

The grommet between the umbrella pole and the hole in the table broke for my patio umbrella, so I made this as a replacement. There are a few similar designs on thingiverse, but they were either too flimsy or not the correct size. The stl is for a...

See the photos for a better description than I can type here. ... Basically I cut out the four center 1" tiles of a 12" square tile and replaced it with this so I can put an umbrella through it. ...

Patio Table Umbrella Pole Bushing Spacer; made to reduce pole movement in the table. ... I used flexible filament, but any filament will work.

Umbrella hole cover for patio table. If you don't have an umbrella and want the hole plugged up. For 2" and 2.25" diameter hole. ... Solidworks 2018 model included.

This is a plastic patio table hole protector so that your umbrella doesn't rub against the glass. I made this because the one that came with my patio table dried out and broke, so this is a replacement. Zip file contains 2 sizes. ... My patio table...

This is a simple plastic thing to cover the hole in a patio table where an umbrella would go with a cover. The .stl is for a 52-56mm umbrella hole which is the standard size - at least here in the United States. The top cover is 60mm in diameter...

Insert to protect glass table from umbrella pole. ...This tightly fits a 2" umbrella pole and may needslight customization for your setup.

This object was made in Tinkercad. ...https://www.tinkercad.com/things/0NGwwwQrmOg

Got a new patio umbrella and lost the protective ring for the glass patio table. 

No longer use the patio umbrella, center plug to fill in the hole missing? ... Print and use this to neatly fill in the hole.

Replacement grommet for the umbrella hole of a glass outdoor table. *** Must be printed in a flexible filament. Print shown was printed in TPU. *** Glass thickness: 5 mm Glass hole diameter: 50.4 mm Grommet Umbrella hole diameter: 40 mm Grommet...

My Auntie needed a new plastic ring to go between her patio table umbrella and her patio table, it's a nice easy fit--if perhaps a bit overkill for the task! Umbrella Pole Dia: 1.5in ø || 38.1mm ø Table Hole Dia: 2.25in ø || 57.15mm ø Enjoy. ... ...

I would assume most patio table and umbrella combos are a universal size. I printed with PETG since it will be in the sun and weather to avoid it warping in the heat. Fits perfectly snug and got rid of a lot of the wobble! Hope it helps someone else...

There are 2 bushings, both for the upper and lower part.

Please don’t forget to rate the model, for us it is very important 3D model available in these formats: 3ds Max 2010 (.max), Autodesk FBX 2006 (.fbx), OBJ (.obj) Scene Statistic below: -Subdivision ON: Polys: 26 902 Tris: 53 672 Edges: 54 418 Verts:...

Please don’t forget to rate the model, for us it is very important 3D model available in these formats: 3ds Max 2010 (.max), Autodesk FBX 2006 (.fbx), OBJ (.obj) Scene Statistic below: -Subdivision ON: Polys: 26 902 Tris: 53 672 Edges: 54 418 Verts:...

Please don’t forget to rate the model, for us it is very important 3D model available in these formats: 3ds Max 2010 (.max), Autodesk FBX 2006 (.fbx), OBJ (.obj) Scene Statistic below: -Subdivision ON: Polys: 26 902 Tris: 53 672 Edges: 54 418 Verts:...

Please don’t forget to rate the model, for us it is very important 3D model available in these formats: 3ds Max 2010 (.max), Autodesk FBX 2006 (.fbx), OBJ (.obj) Scene Statistic below: -Subdivision ON: Polys: 26 902 Tris: 53 672 Edges: 54 418 Verts:...

In my haste I had accidentally left the umbrella open over the patio table. Unbeknownst to myself we were in for a windy AM and I woke to the top half of my umbrella in the neighbors yard...destroyed. I was left staring at half an umbrella pole...

What you see is what you get. Dimensions: 300mm x 300mm I print it upside down (the design file is saved this way) so that the flat side of my printer bed becomes the top layer. NOTE: I used PETG and this design didn't hold up against the...

... No cleaning required - simply drop models into the scene for rendering. Textures included: 'Patio_table_with_umbrella_v_1_cloth_bump.png' (1024x1024) and 'Patio_table_with_umbrella_v_1_wood_diffuse.png' (4000x4000). ...© Leonid Naku [Zurel] 2018.

High quality model 'Patio table with umbrella v 4' specially for your projects.Quality and accurate modeling, allows you to use model in any projects. ...Elaborated all small details, accurate UVW mapping and high-resolution textures make the model more...