patio table clips 3d models

... match the size of my table and then enlarged the central hole to accommodate my metal umbrella shaft seamlessly. You can access the public Tinkercad model for reference: https://www.tinkercad.com/things/4Gu2v6PahnI-patio-table-insert-remix/editv2

We found the hole for the umbrella in our new patio table was 2" wide, but the pole for the umbrella was 1.5". The result was a wobbly umbrella. This shim holds it snugly in place. ...It's designed in two halves, so you can put it in place after...

Our patio table had a 2.25-inch hole in it, which is roughly equivalent to 57.15 millimeters. Our umbrella was just 1.75 inches wide, or approximately 44.46 millimeters. These measurements are precisely what the manufacturer used for the part's...

This is an insert to support the umbrella for our patio table. These support both the umbrella in the holder on the ground as well as aligns the umbrella at the table hole. This is a simple design, but I have provided .STP files so you can modify for...

I designed this grommet replacement for my patio umbrella after the original one broke between the umbrella pole and the table hole. Other similar designs on Thingiverse were either too weak or not precisely sized. The stl file is tailored for a...

There are no cross braces so the table does not have a lot of structural support for horizontal movement (lateral strength.) It should be fine to hold drinks etc that you would place on a patio side table. ... Extra strength could be achieved by adding...

I noticed that the plastic supports holding the glass surface of my patio table have been breaking and falling off. I took one of the broken ones, made some measurements with some guesses as to the screw hole size and center location, and printed...

A replacement spacer/clip is needed for the worn-out ones under my outdoor dining table, which had started to deteriorate due to age. The clips fit snugly into a metal ring and serve as spacers, holding the glass firmly against the top edge of the...

I lost a foot to an outdoor patio table, and I had to create a prosthetic from scratch using one of my remaining feet as inspiration. The design process began on my Windows 10 computer with the help of 3D Designer software. To ensure that others can...

I decided to re-paint my ~20 year old aluminum glass-topped patio table. When I was removing the glass, the plastic (or maybe some sort of resin) supports holding the glass table top in from the bottom were all yellowed and most disintegrated or...

-Patio Table and Patio Umbrella.

-Patio Table and Patio Umbrella.

Getting the patio ready for spring, the ring for my patio table fell apart. ... This fits perfectly into the standard hole of a table and is a quick easy replacement.

This is a plastic patio table hole protector so that your umbrella doesn't rub against the glass. I made this because the one that came with my patio table dried out and broke, so this is a replacement. Zip file contains 2 sizes. ... My patio table...

This is a connnector for a glass topped patio table with rounded rectangle hollow metal legs. Made these as I needed a replacement for a diy refurbishment on my patio table and couldn't find spares to buy online. I'd recommend printing in PETG or...

Patio Shade Extension Rod Holder

Umbrella hole cover for patio table. If you don't have an umbrella and want the hole plugged up. For 2" and 2.25" diameter hole. ... Solidworks 2018 model included.

This is a replacement center for patio table. I printed this for a 68mm center hole, but can be resized to fit. ...The cap is not required but finishes off nicely if you don't have a parasol in the table.

This wooden dining table is a standalone object from my patio asset collection, which can be purchased as a standalone item if you only need this specific object. The metalness workflow was used to create this object, and it's PBR ready. Key...

This bracket serves a crucial function as it attaches to the end of a patio table leg, supporting both the glass table and a metal rim encircling the edge of the glass table. Please note that some adjustments may be necessary, as I have yet to...

This is a basic plastic solution for protecting the hole in a patio table where an umbrella would typically go. The .stl file accommodates a standard-sized 52-56mm umbrella hole which appears to be common here in the United States. The upper cover...

... the innovative platform of Tinkercad, this 3D printed masterpiece was brought to life by Shapeways' cutting-edge technology. Its sleek silhouette makes it the perfect pairing with our matching patio chair, showcased on my website for all to see.

Insert to protect glass table from umbrella pole. ...This tightly fits a 2" umbrella pole and may needslight customization for your setup.

I designed a custom grommet to fit a 50mm wide hole with a thickness of 5.1mm, replacing one on my table that had snapped tabs due to broken locking mechanisms. Since no replacement parts were available, I created a better alternative myself. The top...

Rattan Patio Coffee Table

Patio table by Natuzzi

This project originated from Wood Magazine's Issue No.6 in August 1985 and has been meticulously modeled using Solidworks 2016 software. The stunning renders were achieved with Simlab Composer 8 Mechanical Edition, while GIFs were created using...

1/64 scale patio table and chair for resin printing.

Got a new patio umbrella and lost the protective ring for the glass patio table. 

Custom Patio Umbrella Holder; crafted to minimize umbrella base swaying on the table. ...I utilized flexible 3D printing material, though standard filament can also be used.