parkzone sport cub 3d models
28314 3d models found related to parkzone sport cub.thingiverse
This is a motor mount for the ParkZone Sport Cub 1.3m R/C airplane. A friend of mine had broken his original mount and asked if I could create a suitable sub for him since the part was discontinued. I did and created it in two styles: with and...
thingiverse
... compartment, taking the place of the Velcro strap. ...Secure it with hot glue and add some foam to keep the battery snugly in position. Specifically designed for the Floureon 1500mAh 3S Lipo, this upgrade is tailored to fit Parkzone's Sport Cub model.
thingiverse
Every hard landing would snap the zip ties. These tiny hooks lock onto the wire with remarkable force, and I'll add them for extra security. They're incredibly easy to purchase on-site. I print mine with 100% infill settings to make them as strong...
thingiverse
This creates an ideal mounting spot for Velcro and a Velcro strap, perfectly fitting in the Parkzone Sport Cub S2. I utilize 2200 3S packs in mine and have never had a reliable way to secure the battery until I designed this. ... If you're wondering...
thingiverse
I wanted to design a housing for my parachute men from the Toy Story series that would allow me to drop them from an airplane without having them fall out. To achieve this, I needed a few specific components. Firstly, I required one 9g servo motor,...
thingiverse
Remix of stock motor mount. made the holes fit the stock motor Just made the whole thing 3 mm thick to get rid of support need. ...
thingiverse
These replacement parts apply to the following models: ParkZone Sport Cub 1.3M (currently out of production) HobbyZone Carbon Cub S+ 1.3M The photos below show original Sport Cub and Carbon Cub fairings. ...I made significant modifications to improve...
thingiverse
... precise cuts. You don't have to glue the chopsticks in, but you can if you want to. The jig takes up less space when it's disassembled. This jig applies to these planes: ParkZone Sport Cub 1.3M (no longer available) HobbyZone Carbon Cub S+ 1.3M
thingiverse
Applies to these models: ParkZone Sport Cub 1.3M (discontinued) HobbyZone Carbon Cub S+ 1.3M **Update December 14, 2020** I carefully split the model in half lengthwise and printed each half separately using Solutech Clear PETG. After several...
thingiverse
This is a retainer designed to secure the 1300mah battery supplied with the Horizon Hobby/ParkZone Sport Cub. The design ensures the battery stays firmly in place beneath the black velcro strap. During my flying experience, the battery suddenly...
thingiverse
I am new to 3d modeling but I made this to replace the foam hood for the sport cub s as it was getting broken every time I changed a prop or gear shaft. This will work on the s2 also. Print vertically for no supports. ...As usual feel free to give...
thingiverse
The nose cone on my hobby zone sport cub S fell off from a pretty hard crash so I decided to 3d print a new one.
prusaprinters
This is a 3d printable propeller for the Hobbyzone Sport Cub S V2. ...I find the plane going faster with my propeller than with the stock one. Print settings:No supports0.10 layer height (Brim)
thingiverse
First attempt at creating a replacement tail clip for the Sport Cub S from Hobby Zone. Instructions are in place to achieve this goal, starting with the intention of printing the new tail clip with the base plate down to avoid any issues with...
thingiverse
The battery on my Sport Cub 2S kept falling out when flying so I chose to make this mount. print in sperate pieces with the main chassis laying flat on the logo side, this piece will most likely need supports in the circular holes. print the "lid" on...
thingiverse
This is an upgraded gear for a sports car engine. ...It's the primary gear on the transmission assembly, positioned alongside its smaller counterpart.
prusaprinters
Sport Cub S2 motor mount for Turnigy 3536 motor
thingiverse
Printed this in PLA because my broken part crashed out. May require scaling up. Designed in Fusion360 using my busted piece as a guide. To assemble, you'll need: 7/64 drill bit (2) 40mm M3 allen head bolts (2) M3 nuts M3 allen wrench Drill the...
thingiverse
A great solution for rc flying while in the snow just as a little saftey tip, add Auto generated support when slicing. ... Once its printed put the rectangle in the battery place, it should friction fit
thingiverse
For All of those who love to fly in the snow, Here Is a creative and simple solution. Skis! I would recommend Auto Support Even though I already added some, better To add support than not. ...
thingiverse
Sport Cub S2 motor mount for Turnigy 3536 motor Including Fusion 360 CAD file Upgrade your Sport Cub S2 with this motor to increase speed by 20% I'm thrilled with the results of this mod already Please note ESC recommendations on HK website...
thingiverse
You just insert two batteries into it and place it on top of the controller's antenna.
thingiverse
Repair pieces for Parkzone Vapor / Night Vapor: Motor mount - direct replacement for original. ... Carbon repair tube - contoured for tailplane - insert carbon fibre ends into the tube and glue with cyano.
thingiverse
This replacement platform seamlessly integrates into the Parkzone Trojan cockpit, creating a perfect space for mounting an FPV pan system. Its primary function is to relocate the essential components of the cockpit, paving the way for effortless...
thingiverse
Cover for ParkZone F4U Corsair (PKZ4600) Park flyer-size, with a wingspan of 44 inches or 1118 millimeters. All components are 0.6 millimeters thick, requiring heat to achieve the best layer bonding results. PLA printing specifications include...
thingiverse
I've created this design for my ParkZone Corsair first generation. The motor failed, so I replaced it with an NTM 35-30 1100kV motor. This motor mount stands at 29mm high (originally 15mm). I also fabricated a new spinner to shield the propeller...