parallel battery holder 3d models
442271 3d models found related to parallel battery holder.
thingiverse
Holder for the parallel shims forthcoming. Holds 9 pairs of 3" thin (0.125" thick each) parallels. Nice design, printed quickly ~2 hours. I got some fat inner corners, so the parallels are held very tightly. I'm going to clean up the corners...
thingiverse
This is a premium 7x AA parallel battery holder designed to handle larger currents. It boasts a snap lid, internal springs securing the battery connectors and separate compartments for wiring. Fitted with standard 1.5 mm2 7x0.5mm copper wire...
thingiverse
To learn more about this product, visit http://www.banggood.com/ISDT-SC-608-150W-8A-MINI-Smart-LCD-Battery-Balance-Charger-p-1057271.html?rmmds=search or...
thingiverse
Holder/Box insert for 4" machinist parallels. SAE and Metric sizes listed. ... 6.675" X 4.1" x 1.75" (LWH)
thingiverse
PCB Quantity: M3 x 25mm = 4pcs Buy: ISDT SC-608 150W 8A Mini Smart LCD Battery Balance Charger - https://goo.gl/tLzMZe Parallel Charging Board Supports 5 Packs of 2-6S Lipo Battery XT60 T Plug - XT60 - https://goo.gl/fNCbBS AMASS XT60 Plug Extension...
myminifactory
This is a 4 pen holder for the Pilot Parallel Calligraphy Pen set with an integrated pen rest. Pens can be inserted and screwed in and out with the cap captured in the fitted hole. ...Holds up to 4 pens.
thingiverse
This is a 4 pen holder for the Pilot Parallel Calligraphy Pen set with an integrated pen rest. Pens can be inserted and screwed in and out with the cap captured in the fitted hole. ...Holds up to 4 pens.
thingiverse
IEC 62196 Type 2 Parallel Holder Well, actually not quite; the socket is pointing away from the wall at a 10 degree angle. Print as provided in the STL, best to use supports. The wall mounting holes have a diameter of 5 mm and are designed for...
thingiverse
I crafted a caliper specifically for the ruler I purchased from Banggood.com, which can be found at...
thingiverse
Compatible avec Alesis SURGE, COMMAND, etc.Les vis utilisés sont :2x M6x30 - Têtes hexagonales2x M6x25 - Têtes hexagonalesLes papillons utilisés sont ceux créés par Volt1air :https://www.thingiverse.com/thing:1754127Cette pièce fait partie d'un...
prusaprinters
Original Prusa MINI bed cable holder points cable straight to the rear which can collide with a wall. This model turns cable along the bed so more clearance is available.</p> <p>The +24V cable has to be mounted to the top of the bed while GND has to...
thingiverse
(The nut for the middle pillar may need to go in before the batteries do) Special Thanks to [SamWhiskey](https://www.thingiverse.com/SamWhiskey) for the inspiration on how to route the cabling in the lid and add the fuse in:...
prusaprinters
This is a 7x AA parallel battery holder for larger currents. It has a snap lid, internal springs for the battery connectors and separated space for the wiring. It can be fitted a standard 1.5 mm2 7x0.5mm copper wire normally used in household...
thingiverse
Uses height to model the voltage for a circuit with two batteries in parallel connected to a resistor. ...
thingiverse
A humble tool designed to keep mischievous code snippets organized and neatly aligned, allowing me to grasp even the most stubborn lines with ease.
prusaprinters
Everything prints without supports and assembly with a M3x10 caphead screw.
cults3d
Portable Collapsible Mounting System for Enhanced ARGteck Antenna Compatibility with DJI Phantom 3 Standard Drone
thingiverse
Battery Themed Battery Holder - 8x AA Sized Batteries Yes, yet another battery holder!