paperclip rcm jig 3d models

Included with the files will be a printable jig for the Ghost Gunner created by Flood from FOSSCAD (he’s the best!). Hopefully one of the more GG savvy folks can make a tutorial showing how to set that up on the GG and make it work. I used a...

Then cut a 17 mm long PTFE tube using the printed jig, the PTFE should have an inner diameter of 2 mm and outer diameter of 4 mm which is the standard for 1.75 mm filament. Insert it into the hotend mount. Next, mount the extruder over the...

For example:mount-sherpa-mini-r1-dragon-2.0.stlptfe-cutting-jig-orbiter-2.0-dragon-and-mosquito-2.0.stlThe PTFE cutting jig is for a short piece of PTFE tube used between the extruder and the hotend in the cold zone where it does not deform from...

The 3D printing model's chosen scale is 1:34 for the FFF/FDM version and 1:68 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 150 parts;- A printed ship is 680 mm tall, 443 mm wide, 588 mm...

These pins do not come in STL files but can be made out of short pieces of regular paperclip;- DLP/SLA/SLS 2.0 version of R2-D2 model (1:8 scale) can be displayed in diorama with FFF/FDM 1.1 version of C-3PO figurine (1:8 scale);- It is...

The 3D printing model's chosen scale is 1:34 for the FFF/FDM version and 1:68 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 3.0 version features:- Contains 68 parts;- A printed ship is 189 mm tall, 329 mm wide, 394 mm deep;- There are...

Good idea to make and store multiples ahead of time using paperclips to hold layers together. - Replace heavy duty zip lock bag every 1-3 days. Daily if required for professional lip reading use. Avoids inevitable contaminant build up in zip...

The 3D printing model's chosen scale is 1:136 for the FFF/FDM version and 1:272 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 83 parts;- A printed ship is 298 mm tall, 292 mm wide, 926 mm...

Now screw the aluminium rod (with two nuts threaded on it first), into the rod ends until you have approximately equal amounts of thread in each end and the rod ends fit over the m3 bolts in the jig. Tighten the nuts against the rod ends. Make 5...

Putting them together is quite easy using the original rudder as a gluing jig. Pic 1. Showing sleeve on rudder, glued up, but not shaped or coated Pic 2. I don’t think of these as failures, just “partial successes” :) Pic 3. Left, fresh off printer...

I made a jig out of cardboard so that I could paint 37 of them without too much trouble. I cut out a tight opening so that a shelf sleeve can just go through out of some cardboard, and then I put blue painters tape over the hole (and over the edge of...

To slide down the linear rails, use the MGN-12 jig alignment tools you should have from installing the rails previously, placing one on the top and bottom. Center your X-axis carriage in the middle spot on the Z-linear rails where no screws are...

Set the hands to the 12h position to give them a nice starting point(I recommend using on of the 6 screw mounts for the watchface as a guide. Since the central pin is not supported in this state of the assembly, use the center_jig part to...

In my experience 2 screws are enough but the design allows for four screws to be used.Rotate the hotend so the heater cartridge is the closest to the front of the carriage and the thermocouple towards the blower fan.Then cut a PTFE tube using the...

The heater cartridge should be the closest to the front of the carriage and the thermocouple towards the blower fan.Then cut a 17 mm long PTFE tube using the printed jig, the PTFE should have an inner diameter of 2 mm and outer diameter of 4 mm which...

The heater cartridge should be the closest to the front of the carriage and the thermocouple towards the blower fan.Then cut a 17 mm long PTFE tube using the printed jig, the PTFE should have an inner diameter of 2 mm and outer diameter of 4 mm which...

The heater cartridge should be the closest to the front of the carriage and the thermocouple towards the blower fan.Then cut a 12.75 mm long PTFE tube using the printed jig, the PTFE should have an inner diameter of 2 mm and outer diameter of 4 mm...

The heater cartridge should be the closest to the front of the carriage and the thermocouple towards the blower fan.Then cut a 12.75 mm long PTFE tube using the printed jig, the PTFE should have an inner diameter of 2 mm and outer diameter of 4 mm...

In my experience 2 screws are enough but the design allows for four screws to be used.Rotate the hotend so the heater cartridge is the closest to the front of the carriage and the thermocouple towards the blower fan.Then cut a PTFE tube using the...

The fibers will not line up if you don't.LED strips should be alligned with LED's 30 (in the middle), not from the start, as the outer strip LED's will shift more to the side at the end.Technically only the data channel needs to be bridged here, if...

The fibers will not line up if you don't.LED strips should be alligned with LED's 30 (in the middle), not from the start, as the outer strip LED's will shift more to the side at the end.Technically only the data channel needs to be bridged here, if...