paneldue 3d models

This is an enclosure for the PanelDue (https://miscsolutions.wordpress.com/paneldue/) with the 7" LCD specifically included with the package from Filastruder (https://www.filastruder.com/collections/electronics/products/paneldue?variant=16552844356),...

This is a custom adapter for mounting the PanelDue on an E3D BigBox printer.\nThe adapter fits perfectly in place of the original LCD screen.\nTo secure it firmly, four M3 screws with fine threads are used - the same type often employed to hold...

Leave it loose if you prefer to lift it occasionally, or secure it firmly with a double-sided tape.\r\n\r\nThe Case Bezel screws directly into the PanelDue and then attaches to the Case Top via a sturdy connection. ...Meanwhile, the Case Bottom connects...

This is a housing for the PanelDue 5i Clone by Fysetc (https://de.aliexpress.com/item/33004947638.html?spm=a2g0s.9042311.0.0.27424c4dqdux2o) Please note that the FYSETC version of the 5i differs from the original one. There are two versions...

Big Thank You to kuhnikuehnast for the PanelDue angled case! This is the only case I could find on all of Thingiverse that perfectly fits the current (2019) version of the 7" display. However, the case is intended to be mounted to aluminium profile...

I am working with the Paneldue 5i" from FYSETC, featuring slots for the SD card and MicroUSB port, along with a cutout on the back for reset and erase buttons. This display can be driven using either the 4-way cable or flat ribbon cable, with the...

This is a custom enclosure designed to house a Duet Paneldue 5" **V2** display based on Davids' original concept. The design is optimized for mounting on a 2020-type profile and allows the backpanel to be installed upside down if desired. The top...

PanelDue 5" Compacted case w. hidden wires is a very compact box where everything fits inside. Prepared for SD card usage. Assembling and BOM The rear PCB attaches to the rear part of the case with 3x m3 6-mm screws. The Front and rear parts are...

I made this design because I wanted to place my 7inch screen in the middle of my E3D Tool Changer, but current designs are asymmetric due to the PanelDue controller board being mounted directly to the backside of the screen. To resolve this issue, I...

This enclosure is designed specifically for the PanelDue with 7" LCD that mounts to the bottom frame 2020 extrusions on my Ultibots K250 Delta printer. It slopes the face and makes it perfectly height-adjusted for using from a desk chair in comfort.

This is an alternative mounting frame for 15mm extrusions specifically designed for the PanelDue 7i Case from LumberjackEngineering. I created a 15x15mm version with an optional hole for cable management that can be used to hide cables inside the...

This is a Housing for the PanelDue 5i Clone by Fysetc ( https://de.aliexpress.com/item/33004947638.html?spm=a2g0s.9042311.0.0.27424c4dqdux2o ) Please note that the FYSETC Version of the 5i differs to the original one! There are two versions. One with...

I designed this layout because I wanted my 7-inch screen in the middle of my BigBox, where current designs are off-center due to the PanelDue controller board being directly mounted on the backside of the screen. To compensate for this, I created a...

You're looking at a slim case designed specifically for the PanelDue 4.3". It measures a total of 16mm in thickness. The matching case for the rear PCB also boasts the same thickness, standing at 16mm. This enclosure is intended to be mounted...

This is a Housing for the PanelDue 5i Clone by Fysetc ( https://de.aliexpress.com/item/33004947638.html?spm=a2g0s.9042311.0.0.27424c4dqdux2o ) Please note that the FYSETC Version of the 5i differs to the original one! There are two versions. One with...

Big Thank You to kuhnikuehnast for the PanelDue angled case! This is the only case I could find that perfectly fits the current (2019) version of the 7" display.</p><p>However, the case is intended to be mounted to aluminium profile poles, but I...

I have also added parts for PanelDue 7i. You need additional parts for this design: 1. M3 inserts: ...

I think without the Neopixels it looks more modern and clearer.I have also added parts for PanelDue 7i.You need additional parts for this design:M3...

I have just been informed that this will not fit the PanelDue Integrated version of the PanelDue 7i. Sorry Garrystr!!! I have remixed the case for the new version. Garrystr has also put out a basic case that will fit the new version:...

This remix, I made quite a few adjustments to increase the size, add some tolerance to the bolt holes and around the screen.I found my panel was off centre on the board, so I made a model which the cutout for the panel can be moved and cut if you...

I had to break this large design up because it wouldn't fit within the boundaries of my printer's bed, so I cleverly divided it into two distinct sections.