paneldue 5i 3d models

I wasn't thrilled with some of the 5i mounts that were floating around out there. The screen wasn't exactly aligned in the same spot as where Ben had envisioned for the PanelDue5, which threw off the entire aesthetic look.\r\n\r\nThis revised mount...

... ** UPDATE 2-7-21 ** After printing the design it looks like there was a slight variance between the positioning of the PanelDue in the opening on the enclosure. I shifted the mounting holes for the LCD up 1.5mm and brought the 2 sides in 1-2mm. ...

A simple remix of the PanelDue 5i front case piece to suit mounting to the Seckit SK-GO. ...This part is required as well as the "5i_Case_Rear.stl" part from the original file set: https://www.thingiverse.com/thing:2799628/files

A simple remix of the PanelDue 5i front case piece to suit mounting to the Seckit SK-GO. ...This part is required as well as the "5i_Case_Rear.stl" part from the original file set: https://www.thingiverse.com/thing:2799628/files Category: 3D Printer...

A simple redesign of the PanelDue 5i front case piece to fit mounting on the Seckit SK-GO, necessitating the inclusion of this component alongside the "5i_Case_Rear.stl" piece from the original Thingiverse file set located here:...

A design exercise to enable swapping out the standard Ender 3 LCD support with a PanelDue (5i or 7i, your choice). Untested, I've created these designs using 3D models as reference. STEP files are included for further modifications if needed. ... July...

Here is a simple mount for the PanelDue 5i that perfectly complements the Anycubic Delta Linear Plus. It prints flawlessly even without any support structures, which is a major plus in my book. ...However, one thing to keep in mind is that you'll need...

A design exercise to allow replacing the standard Ender 3 LCD support for a PanelDue (5i or 7i, your choice). Untested, I've made these designs using 3D models as reference. ...STEP files included for further modifications if needed. July 1st, 2019:...

... ducts. This has worked well on multiple displays over several years without issue. The PanelDue 5i case needs supports only for the SD card slot opening; no other support is required. ...I printed it with PLA since high heat is not involved.

PanelDue 5i case with usable SD card access. Uses 7 M3 4mm x 3mm inserts and M3 bolts (4-18mm and 2 6mm) or longer M3 bolts (4- 22mm and 2 8mm) and nuts. Many people say a 30cm cable is the longest you can use reliably with the SD readers but I made...

This is a front mount bezel designed for the PanelDue 5i used in Wanhao Duplicator 6 or Monoprice Ultimate 3 printers. It's low-profiled and matches the curve of the chassis for a sleek look. A door can still be used, but the front edge will need to...

This Cover Is A Panel Mount Created By Due To The Fact That Current Firmware Does Not Allow For Complete Display Shutdown While The Printer Remains On, I Felt It Would Be Nice If The Light Didn't Show When Pausing The Printer At Night. This Is Why...

This is a custom panel mount designed to conceal the printer display. The current firmware doesn't allow for complete display shutdown while the printer is operational, so I created this cover to solve that issue. When you pause your printer at...

... what's left of it. ...I made this to fit the Paneldue 5i clone from Fysetc and the metal structure I added to my machine, but it also works with the standard printer and other machines that use this design. ...I've also included a slot for the SD card.

Longer screws (M3X10 should be fine) can be used without running into the back of the PanelDue 5i PCB. You will also need eight M3 nuts. Parts Used for Both the 5i and 7i Cases: Two M5x30mm bolts are required to attach the arm to both the back of...

I'm using a FYSETC PanelDue 5i on my BLV cube so I had to adjust the front panel a bit. The size is the same as their TFT81050 5inch TFT and will fit as well. ... I use M3x5 screws to mount it.

This case mounts the PanelDue 5i by Duet3D on a 2040 Extrusion, expertly angled for optimal viewing. All buttons are readily accessible, including reset and erase options. The reset button is designed for effortless pressing, while the erase function...

... Are Adapted for Ruthex Thread Inserts.\r\nThe Mount Is for 30x30 Extrusion. ...I Use This Version for My Zaribo Printer.\r\nMaybe Someone Could Need This for His Cloned PanelDue 5i.\r\nYou Can Also Find the Step File in My Uploads.\r\nBest Regards

This is a Case to mount the PanelDue 5i by Duet3D on a 2040 Extrusion. It is angled to give the best view when mounted. All buttons are accesible (reset; erase). The reset-button is easy to press and for the erase button, you will need a pen. I also...

Installed a bezel lcd holder to my Rostock Max 3.2 unit using the spare cover plate. This enables smooth control of the printer without any need for tethering, allowing you to use the SD card directly on the LCD instead. The SD card is easily...

This is is a remix of LumberjackEngineering's PanelDue case for the original Duet display.I modified the case for the clone version (from fysetc 5 inch V3).What I changed:Cutout for flash cable and SD cardCutouts for reset and erase buttonCutout for...

I bought a FYSETC PanelDue clone, available at https://www.aliexpress.com/item/4000152814384.html, and upon receiving it, I realized that "clone" might not be the best description since it is more like an inspired design. From the product images, I...

I purchased a FYSETC PanelDue clone (https://www.aliexpress.com/item/4000152814384.html), and I soon discovered that "clone" is not an accurate description, as it's more like an inspired design. It was clear from the product images that this device...

I revamped the design from JenPet to accommodate the SD slot and the four-pin connector.

Paneldue 5i clone mount for use on my Hypercube. Used F2D-SolidInk's design as a base for the display housing. Print 1 housing, 1 angled mount, and 1 mirrored angled mount to use. solidworks file included for modifying the bracket if needed. ... ...

I'm using Paneldue 5i clone mounts on my Hypercube. The design for the display housing is based on F2D-SolidInk's original work. I printed one housing, one angled mount, and a mirrored version of the angled mount to suit my needs. ...A SolidWorks file...

... Touch Screen Upgrade. ... Designed and crafted with precision for a friend's Ender 3 3D Printer, this custom case seamlessly integrates the Fysetc 5i clone and PanelDue touch screen upgrade, enhancing overall functionality and aesthetic appeal.

Replacing the Original LCD Screen on a FlashForge Creator Pro 2016 with a PanelDue 5i Upgrading my FlashForge Creator Pro 2016 printer required replacing the original LCD screen with a more advanced option, the PanelDue 5i. This upgrade was essential...