palette 3 pro 3d models

If one wire roll used at the input doesn't roll anymore (wire is stuck in place), the Palette 3 Pro will move forward in the direction of the rolls until it falls off from your table. It happens to me. I designed in Fusion 360 an adjustable bracket...

I was having trouble finding relatively fast 8 color test print for my palette 3 pro, so I made one. ...It is designed to be printed with .2 layer height.

I was having trouble finding relatively fast 8 color test print for my palette 3 pro, so I made one. ...It is designed to be printed with .2 layer height.</p>

If one wire roll used at the input doesn't roll anymore (wire is stuck in place), the Palette 3 Pro will move forward in the direction of the rolls until it falls off from your table. It happens to me.I designed in Fusion 360 an adjustable bracket...

this is a clip for the ender 3 pro and palette 3 pro. it uses the supplied Velcro from mosaic. ...it gets attached to the 2 screws holding the Z lead screw nut.

8port - 6mm for palette &nbsp;3 pro

This is a coaster I designed to use all the inputs on my new palette 3 pro, but surprise! When I went to print it, I was one color short. O well, here is a nice 7 color print to test your palette 3 pro with. ...I printed it using p2pp.</p>

Clip de fixation Tube PTFE de la Palette 3 Pro sur extrudeur de la 3DEER MK300PTFE tube attachment clip for the 3 Pro Palette on the 3DEER MK300 extruder

Clip de fixation Tube PTFE de la Palette 3 Pro sur extrudeur de la 3DEER MK300PTFE tube attachment clip for the 3 Pro Palette on the 3DEER MK300 extruder

This is a support holder replacing the original base to use the Palette 3 Pro upside down. No assembly or screw. ...it just fit like the original base but on the other side.

Replacement pillow block for the 10mm bearing on the feed gear for Palette 3 Pro. Printed at 100% infill. It was easy to get the bearing out of the original part because it cracked. ...I made the hole in the at 10.34mm since I had to force it in on the...

Made this simple mount for my Palette 3 Pro for my Voron V2.4 frame (2020 alu extrusion).Recommend printing it with 4 perimeters, 40% infill.Needs 2 M5 Tnut or BallNut and 2 M5x16 screws.Be aware if mounting Palette upside down as the mount flange...

https://www.youtube.com/watch?v=9l2fjvfEEqk if you want to make it just like me you can load the filament in the palette 3 Pro... 1. Blue 5. White 2. Green 6. Orange 3. Yellow 7. Red 4. Purple 8. Black My printer is a Creality...

Developed for a friend who needed to organize his filament storage and feed solution on his palette 3 pro. USES PC4-6 fittings and normal PTFE 4MM OD, 3MM ID. Here are his sources. ... ...

Developed for a friend who needed to organize his filament storage and feed solution on his palette 3 pro. USES PC4-6 fittings and normal PTFE 4MM OD, 3MM ID. Here are his sources. ...

Developed for a friend who needed to organize his filament storage and feed solution on his palette 3 pro. USES PC4-6 fittings and normal PTFE 4MM OD, 3MM ID. Here are his sources....

This is a filament input tube holding clip for the Palette 3 Pro. It allows filament to be fed in by 4MM OD tubes (similar to those used for standard Bowden tubes) I use this to prevent the filament from accidentally slipping out of the Palette as I...

... in the guide for this function.</p><p>I printed those guide in black Materio3D PETG. You just need 24 No. 10-24x1 inch long screws.&nbsp;For the input entrance of the Palette 3 Pro use the following part:https: //www.thingiverse.com/thing:5261015

... a hole in the guide for this function. I printed those guide in black Materio3D PETG. You just need 24 No. 10-24x1 inch long screws. For the input entrance of the Palette 3 Pro use the following part: https: //www.thingiverse.com/thing:5261015

This is an adapter to connect the Mosaic Palette extruder tube holder to. ... I did drill an extra hole in the aluminum, but not necessary.

... with setting my loading offset and Esteps. P.S. If you like my work check out more here! https://www.printables.com/@ATrain08_611047If your looking to calibrate your Esteps I found this video that was very helpful for my Ender 3 pro and Ender 3 s1:

Everyone having used the dust filter for single extruders know how much dust gets caught over time.&nbsp;I wanted to protect my Palette from that so I made this remix.Thanks for downloading :)&nbsp;&nbsp;Added another version without single holes for...

After making a tube connector, I wanted the Palette a little higher off the table. I made this to raise it 50mm and added a storage drawer. I have a solid one without the drawer as well, if anyone would rather have that one. It works great, but you...

... to the thumbscrews by the inputs. &nbsp;4mm OD PTFE. &nbsp;Decided to go with a friction attachment so that if there is an issue the tube can remove itself from the block without damage.&nbsp;Printed mine in PLA at .3 layer height. ...&nbsp;</p>

This is for connecting the Palette 3/ Palette 3 Pro filament outgoing tube to your Prusa printer. These are designed off provided specs from Mosaic and use the original Prusa file for the filament cover. ... Will update as needed Included adapters...

There wasn't a great filament adapter for the Ender 3 V2 out there so I designed this one and it works really well. You'll need to print the clip as well. See photos. ... This mounts to the printer using the two screws for the Z motor lead screw...

Replacement splice core cover for Palette 3. Print as loaded with supports and 100% infill. Should work. ...Ill do any adjustment that are needed if i can.

Replacement splice core cover for Palette 3. Print as loaded with supports and 100% infill. Should work. ...Ill do any adjustment that are needed if i can.

So in my infinite wisdom I decided to leave my Palette3 Pro in front of the 3D printer- and at the end of a print the moving build platform homed and sent the device smashing to floor- snapping the plastic part that retains the intake roller. ... It's...

this retainer is used by the mosaic 3 (pro) if lost or defect u can print a spare one. i would recommend to print it in petg 0.15mm height. ...after printing use a 2mm drillbit to open up the hole a bit (not tomuch) print 2 on each side of the print bed...