pakistan modeling

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

 This model is currently a working draft. Solar astronomy has inherent dangers, please be sure you understand these (see also below). Use is at own risk. More general information about this approach to solar astronomy can be found at the Sol'Ex...

If you have a printer, then you have such electronics! PaScn3D connection to Prusa 3D printer in a minute (tested!) – dedicated mounting brackets, components adapted to the dimensions of the device Modularity – adaptation to other printers without...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

The design uses 12 '10mm x 3mm' (the magnets are actually closer to 9.95mm x 2.67mm).This is a spin-off from my earlier light-pull magnetic door catch: https://www.printables.com/model/209370-magnetic-low-profile-floating-head-quiet-door-catc , but...

Load your Model into PrusaSlicer and assign both materials. Prusa provides a quite helpful database on their website on how to use all the features in their Slicer that are related to multi-material-printing. After changing the filament there is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

There were points where I’d get 0.4 and Edwin would be 0.5 with his ruler while using the same model. Chances are that we used a ruler that was slightly wider than what 1mm is in reality.</p><figure class="image image-style-align-center...

... holes. The decorative plugs are designed to be sacrificial, so if you're going to reinstall the knife strip, just print some more plugs!&nbsp;Check out the humorous remix of this design here: Wall-Mounted Magnetic Knife Strip — Home Decor Spoof.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

IF YOU ARE HAPPY WITH THAT, A LITTLE DONATION WILL BE VERY NICE <3https://www.paypal.com/donate/?hosted_button_id=5F525DYM8GXK4 If you want to do a remix or changes to the design, you can get the Fusion 360 and STEP file here:...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

IntroductionThis model provides an effective, low-cost teleprompter for livestreaming and recording. Using a Raspberry Pi and Pi Camera (the cheap, non-HQ one provides great full-HD video in this application), your phone to display your script or...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

... weapon. By Alex Wellerstein, a historian of science and an assistant professor at the Stevens Institute of Technology, in New Jersey. Attributions: •Screwdriver by user DAPE, Cults3D (under CC-By-Sa-Nc). •Demon Core modeled by Szadros. ...

This should be the first unit from the power supply mob unit -&gt; this contains just leds and has 2 holes in the bottom for an input line and output line end cap unit -&gt; this contains just leds and has a single input line hole in the bottom The...

Printing Recommended slicer settings: Resolution: 0.1mm - 0.2mm Infill: 10% - 20% Supports: Doesn't Matter Rafts: Doesn't Matter License The "Customizable Arduino Nano LED Candle (2 - 6 LEDs)" model (.stl) is licensed under the CC BY license by Code...

It does not need power to work, it is simply a switch that opens when the sensor tip touches a surface. It is probably NOT suitable for a 3D printer bed leveling system because it could touch the model you are printing. If you added a removable cap...

Both uploading and downloading a few dozen bricks is a pain :) However you can get all: STL.zip contains all the blocks I made so far STL-sets.zip include multiple brick sets for printing (difficult and not so often updated !) source.zip...

This model includes both a solid and a honeycomb version whether you want to print a more authentic and traditional version of the warlock or if you want it to be more unique.&nbsp;I used absolutely bottom of the barrel parts to get this to a fully...

IntroductionMany designs like RC cars and trucks, lanterns, model houses, etc. would benefit if 3D printing could be used to create truly transparent window panes. But as you might know, FDM printing transparent filament per se does not result in...

Depending on the figurine put on top of the box a different playlist ist played, currently mostly kids audio books and a spotify music playlist.All in all a very cool project that i hope to expand when my son grows older.ElectronicsPhonieboxRaspberry...

This model involves many grams of material but also many hours of slicing, printing and overwatching your printer. I suggest you to print the main parts in 0.2mm layers if you don't want it to take forever :S and use something between 0.4 and 0.5 mm...

... and the stuff that I put in that spot. As always, the .blend file for this model is available to my patrons at https://patreon.com/VirtuallyJason. ...If you appreciate my work and have a few dollars to spare each month, please consider joining!

* Remix this model so I know my script is getting used! 15. ??? 16. Profit! Tips: 1. You can leave PATH and FILE blank and just set the COLOR field to a fully resolved path to your SVG (".svg" is automatically appended) 2. You can import the...

I did not integrate this into the grill itself as you might want to swap the location of the pi to either side based on your preference.I appreciate any tips to support my work!Print SettingsPrinter Brand:CrealityPrinter:Ender 3...

If this is true, the topography in this model is still extremely exaggerated to make it more noticeable, about 15% of the radius, giving the model an egg shape. The star-facing direction (since it is tidal locked) of every model in this post is the...

If the format you use is not yet in the downloads, let me know, I will create the models for it. Now print the test part (#0 testmodel) start with the smallest tollerance and try to push the test part over the profile, it should not go strongly...

Comments and suggestions are also very welcome.Update 2020-10-19 Kermi radiator mount clips now availableQuite a few new MultiClip Objects in the collection (link above).Update 2018-09-21 Updated the alignment helperNew: MultiClip Glue!Update...

Also, I am considering some re-design of the right motor plate that currently interferes with the model fan duct. That would recover a bed Y-dimension back to 220. So, after all the print area will be 210x220mm... Parts to print: all parts at last...