painting pla 3d models

The photos show a comparison of my 55° mushroom test (https://www.thingiverse.com/thing:2005832) on a PLA print between this duct, the v6 dual duct, and the stock duct. The result from the stock duct looks more decent than what I expected while I...

The hubs can be reused!Filament usageFor a spool with 80 mm axle diameter, structural size of 8 mm, printed with 15% infill, no rafts and no supports:Hub:23 gSpoke:9 gLabel:12 g  Total for spool with two hubs with standoff, three spokes and...

-- Overall Print Settings for All Parts: 0.4mm Nozzle Your material of choice (I went with PLA) 0.2mm Layer Height on all layers including First Layer. 0.45mm Extrusion Width on all settings, exception: 0.42mm on Top Solid Infill All parts are...

5015 fans blow a LOT more air, so if you have print quality issues, you may want to decrease fan speed for PLA to 70-85%. I couldn't find much info regarding the Sherpa filament screw tension, so with the fan removed, I screwed it all the way...

PLA is fine. I used PETG. 2. Assemble the two halves of the auger. Note that there are 2mm pin holes, one at the tip, and two at the base, to insert 1.75mm filament pins for easier alignment while gluing. Don't forget to install the square nut at...

# HARDWARE If using the original bumper and follower: - (2) 8mm self-tapping M2.6 screws - (1) Foamblast replacement drum spring If using the modified bumper and follower for square springs: - (2) 8mm self-tapping M2.6 screws - (2) 6mm self-tapping...

Harder filament than PLA should work better IMPORTANT !!! I have been let down by the bolt supplier who indicated that it was possible to obtain M4 Hex head part threaded bolts. It appears that the smallest Hex head part threaded bolts are M5 size:-...

I recommend 70% gyroid infill for PLA. Also updated spacing with original LM8UU mount and narrowed the LM8UU slot. **END of EDIT 1** I did not include an extruder mount in the design since I am trying to reduce the weight on the gantry as...

Entry panels, hatches, and more!No support requiredThe code and model files are using “Hatchbox” pla. ...Change if you are using something else (trying to use up what I bought a few months ago.)</li><li>Use variable height to smooth out the curves on...

I will answer as fast and as much as I can. And please, share your makes! Print Settings Printer: Wanhao i3 Duplicator Rafts: Doesn't Matter Supports: No Resolution: 0.2 mm Infill: 15% minimum Filament: Your favourite filament brand PLA Notes: The Y...

I printed mine on an Ender 3 Pro with a 1.0mm nozzle in PLA+, but these designs should be tolerant to other materials and nozzle sizes. You will want to rotate the bucket inlet to print with the flat side (with the circular hole) against the...

You might need to experiment with your speed controller to find out which speeds work well, mine has low speed set to the lowest speed that the compressor would reliably run at.Motor cooling seems to be adequate, I've monitored the temperature of the...

So I'm creating them for you!Here down below there's a list of the packs available that you can check out (it will be updated everytime I post a new one!):Anime pack 1 (2022/03/12)In case you want me to customize it for you I take commissions for 1€...

There is also a version that does not have any holes if you only plan on using the pedals with the triggers.The hinges are designed to be used with un-extruded 1.75mm PLA. Simply slide it through and trim the ends.&nbsp;</p><figure class="image...

Glass doesn'€™t seem to be very good at holding PLA even at 60 C, I haven't tried any higher, but coating it with Kapton tape works great. After cool down, the only think holding the piece in place seems to be the residual surface tension,...

(On completion of final checks this note will be deleted!)28 April - Added BOTTOM-BRACE_125  to the Printed parts schedule.DIMENSIONSTop - 280 x 370mmFrame - 340 x 260 x 400mm  high (13.5 x 10.5 x 19 inches)TOOLS REQUIRED3D PrinterSaw (if required to...

I use PLA because it doesn't lift off at the corners with big pieces. Non-printed parts and approximate costs: One Teensy LC ($12 from pjrc.com) Download arduino 1.8.19 and install the teensyduino extras from pjrc.com...

This can lead to "Heat Creep" issues, if using an All Metal Hotend with PTEG or PLA filaments in lower airflow conditions. I have also provided a set of .050" shorter LED Fan Ducts for certain clone Micro Swiss Hotends that may have a shorter...

(hint: you might also be surprised at how easily you can poke a hole through PLA with a cheap soldering iron ;). If you made it this far and all your lights work, you are over the hardest part of this build. The rest is cake. **Install and...

The differential bevel gears can break with very rough use if they are made from PLA. I eventually printed them from Taulman 910 nylon, which survived my torture tests. -The smallest differential gears need small shafts to hold them in place. Make...

Wells' seminal miniatures game Little Wars. See the sections below for more information. (The toy soldiers in the cover photo are from Earsling's Napoleonics set.) Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes...

It has saved over 40 grams in my print using ABS. Print instructionsPrinter: L200 (Lerdge powered M200) Rafts: No Supports: Yes Resolution: 0.2 Notes: Print the tires with Ninjaflex or Rubber HS or soft tpu. Print the spring with PET or PC, use as...

It has also been designed to allow individual customisation with Lego blocks and/or card cut-outs that insert into custom 3D printed Lego-compatible blocks (the files for the LEGO-compatible blocks for card cut-outs are available here).&nbsp;All the...

&nbsp;If you need another size then request it and I'll post additional files.Jar SizesJarHeightJar...

# Features * Dual sided cooling with dual duct Single 5015 fan duct (with adjustable height) (I've printed up to 65 degrees without issue at 100mms in pla) * BL Touch mount only 43 mm away from the nozzle (Fixed mount) * Nozzle Cam mount for Generic...

Guess why? Prusament PLA or PETG 1kg – I use empty spools to build the device (eco-friendly). If you think that the project should include other spools – suggest which ones.</li> <li>M4, M8 screws, nuts, washers – according to the <a...

Simple bricks to play with or to integrate into other projects, designed to be easy to print, and easy to integrate in all other projects.Printing parameters:PLA//0.4 nozzle//0.2 layer height//0%infill//no support//brim All the parts in the files are...

Recomendaciones de impresión La palanca se puede imprimir con un filamento del tipo PLA. ...La altura de capa recomendada para su impresión es de 0.1-0.15mm y el relleno entre 15-20%.<br/> Es recomendable el uso de soporte para que el redondeado de los...

Your steel sheets now have a new home, slide them in place and enjoy!RECOMMENDED PRINT SETTINGSFilament: PLA (PETG or ABS for heavier duty storage)Nozzle Size: 0.4mmPrint Height: 0.2-0.35mmInfill: 10-20%&nbsp;GEN2 COMPATIBLE PRINTSGen2 Modular Lack...

1x PC power supply jumper: https://www.amazon.com/dp/B01N8Q0TOE/ref=cm_sw_em_r_mt_dp_2rfYFb3Y3XTFV Finally you'll need a way to mount it in your specific printer, for my i3 Mega S I scaled this file in Cura to 80x100mm in X and Y and left Z at 100%...