painting pla 3d models

TPU, PETG, PLA are all tested. TPU had some extrusion failures occurred, so you still need to handle it with care, direct drive won't 100% make it easy to print. 2020.06.10: Initial testing The module assembly was perfect. Then I did finally mount...

The long rectengular shape in the middle could get support because it is easy to take off. The Base part should get around 100°C (I used PLA) or even higher bed temperature to avoid the Warping effect. Turbine blade: Infill: 100% Layer hight 0.1mm...

I used PETG because I imagined that PLA or ASA would be too brittle. I printed them at the highest resolution my printer could muster, which is about 0.07mm. Either that, or it was 0.1mm. Creating A Board I used what I had to hand, which happened to...

I printed mine in PLA with 7% infill, 2 perimeters, and 0.2 mm layer height. The filament I used was scavenged from a dumpster.</p><p><strong>Assembly Notes</strong></p><p>In general, there's only one way for pieces to fit together, so it should be...

I designed a case as compact as possible to be able to fit all component and have opening for every cables.Mounting instruction are given here belowPrint SettingsRafts:NoSupports:NoResolution:0.2Infill:20Filament: Any PETG or PLA Notes:Mounting...

Just make sure to get sufficiently large feet spacers too.Print SettingsPrinter Brand:AnycubicPrinter:Large Size ChironRafts:Doesn't MatterSupports:NoResolution:0.2Infill:10% GyroidFilament: Purefil PLAblackNotes:Actually used my Vyper to print -...

One with hollow text, the other with raised textTwo different 5-coin combination mega coins based on an explanation of the designer's intent/inspiration of a 25-point coinMy "final" version, which is actually only a 20-point coin, but which I feel is...

As a result they are much sturdier than equivalent PLA or PET-G prints might be. Good luck!</p> <p>/edit2</p> <p>I've added two new photos to show my progress so far. The overview photo shows where I am at, approximately. I've wired together some of...

When you install a glass or spring steel sheet, simply position it against the brush holder, and it will act as a dependable stop, ensuring accurate and consistent print bed alignment.To install the Nozzle Brush, print the brush mount preferably in...

Das reicht für PLA. Ein neues Netzteil dran zu bauen ist schwierig, da der UMO auf 19V loift... aber das Ergebnis ist ok ! ...UMO.hex::100000000C9488100C9480130C94AB130C94D6139E :100010000C9401140C942C140C9457140C9482140A...

Assemble flipflop + flipflop-base + lock-TrayThe tray is a great way to finish the run and to store extra marbles. Print SettingsPrinter: Anet AM8Rafts: NoSupports: No, except for “The Wave” and “Lombard Street”Resolution: 0.2Infill: 20%Filament:...

Probably wouldn't matter on shallow cuts but not so good on a deeper one.Print SettingsPrinter Brand:CrealityPrinter:&nbsp;Ender 3Rafts:NoResolution:&nbsp;.2Infill:20%Filament:Amz PLAWhite&nbsp;Notes:&nbsp;To print the socket lid I used supports and...

With eg regular PLA the threads might become almost a bit loose. If you consider this a problem, try to scale down the lamp base by 1-3% in X and Y directions (you can easily do this in the slicer). If you still have problems, then please visit the...

This piece is a little tight fitting, but the PLA should be moderately flexible since the bottom is only 1 mm thick. I recommend flexing it upwards slightly when sliding down a stack of tokens into it to get them in more easily. After that, they...

&nbsp;Don't attempt to make this out of PETG (and definitely not PLA); the deformation could easily get bad enough to start shorting wires together, which could easily bypass some of the resistors, increasing the power output far beyond the intended...

The buckle tang has broken on me once when made from PLA after a year of use, so I have adjusted the file to make the tang 40% thicker (double the bending strength). Or you can just use a commercially available metal buckle (or recycled from an old...

The mount cannot be printed in PLA as it will melt.Print both the main model and the carriage plate hole template. The template will be used to drill a small hole in the carriage to easily fix the extruder motor.Your printer has to be properly...

For the none moving parts a PLA filament would do right and for the moving elements like gears or turbine blades the ideal filament goes from ABS, Nylon to poly-carbonate due to friction, wind etc.A new stl files has been updated with the name of...

However I'd recommend at least three perimeters for larger parts.PLA works well.You need to print things with a "_V2" at the end:2x endBase & endStepperMount8x bearingWashers4x cableMgr...and 1x of everything else with a at the end (assuming I didn't...

(Info on reading Vernier scales in full-screen picture above, as well as here: https://en.wikipedia.org/wiki/Vernier\_scale) Released not fully complete in order to support the ongoing XY calbiration discussion at:...

I used PETG which is quite a reliable choice for this purpose, but even standard PLA should have sufficient heat-proofness for printbed temps up to 150°C (which means about 45°C at the top plate). Please use at least 1.2 mm wall thickness and 40%...

Vivaglory Pet Food Mat Large 24" L x 16" W or Small 19" L x 12" W Waterproof Non-Slip FDA Grade Silicone Mat Anti-Messy Design for Puppy Kitty Dog Cat Small Medium Large Animals...

if you bought SS22F32 switches, make sure that the part name contains "SS22F32"*If you want to have a tracker that uses an AUX/Extension moduleYou would need the following:- *Case_503759_AUX.stl*- *Lid_503759_AUX.stl**The tray is not dependent on the...

There is no HEPA filter, as that would likely require stronger fans/a thicker filter, so it won't filter out potential microparticles, but the active charcoal will filter outgassing from ABS/ASA.&nbsp;The bottom of the rails (20 mm wide) work well as...

The reason is it's more flexible than PLA and there's less risk to break the cable holders.Hint: Don't remove the print from the printer until the base plate has cooled down. It's the best chance for it to stay straight and do not bend while...

- REALLY!I used the same motor form the Poorman's JOBO projectHERE: https://www.prusaprinters.org/prints/65563-poormans-jobo-film-tank-agitator-rockbullet-tumbleHere is the link to the...

PLA + also works but is susceptible to warping in hot environments so I don't recommend it for serious use. I did design this part to be machinable so you could theoretically machine these from a polymer or even metal but that would be heavy and...

I'll get you your custom STL in less than 24h, usually right away.Step 8: PRINT THE LCD PROTECTORPrint the back glass protector 0.8mm.stl in something rigid (like PLA) and glue it into the recessed spot on the back of the mount. Why? In hard crashes...

Jessisimpsonart chose to add a Velcro to the supports to hold it together as an alternative. If you would like to download the Fusion 360 model see make project page here: https://gallery.autodesk.com/fusion360/projects/t-rex-tape-dispenser Reviewing...

If you are using PLA, cyanoacrylate glue like Gorilla-glue or Super-glue should work. - First, apply glue or acetone and insert the TOP INNER part into the TOP OUTER part. The TOP INNER part should sit on top of the inner thread of the TOP OUTER...