paddle tires for traxxas slash 3d models

... at the horizontal screw-holes, which I resolved via the "support enforcer" option in my slic3r software. After several hard bashing sessions, I'm extremely satisfied with the results. I highly recommend trying out ABS for even greater stiffness.

A simple plate for mounting esc's to the slash. Uses stock mounting holes and stock screws, the heads are countersunk for a flat mounting surface. Use double-sided tape to stick the esc down, it works extremely well. ... Install video here...

For my Slash 4x4 ultimate, as a replacement for the original VXL 3S controller The adapter can take controllers up to a maximum width of 40mm Controllers are available here>>> https://amzn.to/33UHdMk Video: https://www.youtube.com/watch?v=74zSqdlPX2Y

I'm doing a slash speed run project without breaking the bank by opting for plastic alternatives instead of metal. They're not only affordable but also incredibly lightweight, making them perfect for printing with ease - the end result is...

I have not attempted to print it yet, but the dimensions are the same. Print instructionsCategory: Toys & Games Summary These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear...

Traxxas rear uprights. Stock look with a little more strength added in with rounds. I haven't printed this yet, just measured and drew it up. ... So it may need a few fixes in the future.

These short arms I designed specifically to accommodate a Lightning McQueen body on a Traxxas Nitro Rustler chassis are quite impressive. ...Stock Bandit rear arms were used in their construction.

Battery Tie Down with a solid center section to allow the mounting of ESC and Receiver as far back on the slash chassis but keeping the weight centered.

I wanted to mount my old Slash body on the wall so I made this I have not printed this yet so it might not work

Body Mount Extension as Add-On to the original Body Mount of the Slash 2WD to fit the Proline F150 1979 body in the front. ... Built with Tinkercad.

These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear arms were used. Added V2 model. ...I have not attempted to print it yet, but the dimensions are the same.

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more...

The bearings are available from traxxas or here cheaper: http://www.kingheads.com/product_info.php?products_id=934 UPDATE 05/05/15: I've updated the design to allow for two motors with a reverse mount on one side. UPDATE 06/16/15: A friend of mine...

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more flush...

you can use this for lift your body. ... Print 100% infill, 0,2mm layerheight

wiper legth 75mm less, need 2mm hole thru body for mounting

you can use this for lift your body. ... Print 100% infill, 0,2mm layerheight

Remix , just added some structure to be able to print without support under the guard But for my shocks it was too small, just created a bigger one for bigger shocks with bigger diameter : https://www.thingiverse.com/thing:4855113

Remix , just added some structure to be able to print without support under the guard But for my shocks it was too small, just created a bigger one for bigger shocks with bigger diameter : https://www.thingiverse.com/thing:4855113

Same part as https://www.thingiverse.com/thing:3353778 just gave it a flat for easier printing.

I Made This Quick Adapter For A Buddy Of Mine, Perfectly Suited For Up To A 30mm Tall Battery That's Mounted Sideways, And Allows Straps To Be Run Underneath The Battery For Secure Holding In Place. No Fussing With Breakable Tabs Here, But You'll...

To assemble the two parts, six M3x16 screws are required: three to join the components together and another three for securing it onto the chassis - four on the nerf bars and two at the front. The version displayed in the picture was a prototype that...

a simple remix of the cover made by asciencepotato. ...added a honeycomb pattern for added durability and also to protect the battery from debries.

ENThese spacers for 4x4 LCG chassis allow you to fit a 2S LiPo battery in a hardcase into battery tray with stock hold-down retainer.RUДанные проставки позволяют вместить 2S LiPo аккумулятор в жёстком корпусе.

I'm new to designing so this was a good thing to try for my kids rc cars that helped me learn some design stuff. ... The little bit of testing we have done so far they have worked great.

I was hunting for a front bumper that would perfectly replicate the sleek design of a Losi 8ight's front bumper for my Backslash project, but unfortunately, my search fell flat. Undeterred, I decided to take matters into my own hands and create one...

I built this without realizing there were shims available for the support strut, But overall I'm glad I did because if mine breaks I can 3D-print a new one. It also allows you to still use a dirt guard like the one shown in the pictures. I printed...

In spring, I lost a retainer at the track; rather than buying a replacement, I opted for DIY 3D modeling (first attempt). Constructive feedback is appreciated. As it's untested, durability isn't guaranteed. Thinner areas might cause issues in certain...

... can run regular packs or shorty. ...The arrangement of the holes and notches allow 2mm incremental movement. A 2mm pin is required for the hinge, 2mm bolts and nuts hold the notched piece in place, and 2mm bolts to attache the tabs to the hold piece.

... on by 2 screws in the original location on the chassis. Plate is 3mm thick. Prints very easy with no supports. 0.3 layer height is fine as there is no detail. I use 2mm walls and top and bottom with all my prints for strength. ...30% infill is fine.