p1p camera 3d models

I have a newer model  https://www.printables.com/model/392851-bambu-lab-p1p-camera-mount-for-nest-yi-and-blank

A redesigned camera mount that fits the Wyze v3 perfectly. I remixed the Original by PrinterPro to make it thinner and use less material. It fits specifically the Wyze v3 Camera very snugly. ... Printed in PETG, I used 4 Walls and 25% Gyroid, also...

... hole on the side to help reach one of the screws. Using a pair of tweezers to hold the screw helps.@PrinterPro has a similar model for a WYZE cam that gave me the idea.https://www.printables.com/model/347802-wyze-p1p-camera-mount-bambu-lab-p1p

So I did my own holder for original internal camera. As U can see, view angle is better, but not perfect. I used 3M double sided pad that I get with printer. For printing I recomend PETG. No support.Po tisku jsem na kameře neviděl hotový model a tak...

https://www.printables.com/model/347802-wyze-p1p-camera-mount-bambu-lab-p1p NEED FOR MOD AND ARTISTRY-Only things needed are some strips of double sided tape, i used T-Rex 15lb tape and used 2 strips to mount to my printer and then one really small...

Right after getting my P1P I sold my Ender 3 V2, but kept the Beagle Camera. Since the camera on the P1P isn't that great I made a mount for the Beagle Cam. With the newest firmware it will allow time-lapse independent of the printer connection. I am...

Printed the remix Bambua Lab X1 Rear Mount Camera by Holger | Download free STL model | Printables.com (that was remixed from https://www.printables.com/model/370982-bambua-lab-x1-p1p-rear-pi-cam), and  experienced reduced picture quality from the...

I originally had an old phone mounted on a similar mount, but it was using some freeware, that had not so great quality.So i found the DCS-6100LH for ~9€, and it gives me 1080p, can reccomend for the...

This is a remix of the P1P Faceplate. ... Mandalorian inspired.

for p1p and pegboard (logo bambu lab) AMS necessary

Work in progress until the Beta test. ...The day of receipt of my p1p.Travail en cours jusqu'au test bêta. ...Le jour de réception de mon p1p

A lightweight, simple and non-adhesive LED bar mount for the P1P printer. ...Nice if you like the "tech look" of the "stripped down" Bambu Lab P1P, a great printer!

Bezel for the P1S/P1P display.3D Print The World. For the people by the people. ...Allowable for remixes.

Allows for lid to be used on bambu lab p1p without ptfe tube obstruction. ... Made for 4mm OD.

Magnetic poop bucket for P1P using 6x3mm magnets Bucket gets attached to magnetic frame with m3 screws

This Design doesnt fit at the P1P Build-Plate, so i remixed it with a Joint-Plug to get it printed on the P1P. If you print it, pls show your results to get it working for all who need it. Printed on P1P with PETG, standard 0.2 Profile on...

I remixed the original mount to make it sit more flush with the frame. ...Original file found here-https://www.printables.com/model/448490-bambu-p1p-wyze-cam-3-mount

Bambulab P1P Pegboard file holderIt can hold set of 6 files. ...Holes for files are 3.6mm so it should work with loads of cheap file set's. Supports for hooks needed

Original modplate is here: https://wiki.bambulab.com/en/p1/modplate-customization Back side cover part with hole for ptfe tube bracket from here: https://www.printables.com/cs/model/333616-bambu-lab-p1p-ptfe-tube-bracket/files Up cover for glass...

But cheap filaments will clog even the best printers and the P1P is kind of annoying to clear because you have to remove the extruder but if the filament is jammed you have press out the gear wheel. [Bambu official...

Thanks to the original Designer https://www.thingiverse.com/thing:5746805 The rear of the P1P is left open with the Bambu published mod plates.This extends the rear cover to drastically reduce heat loss. He still left some gap to make sure there was...

Bambulab P1P Budget Enclosure Project. Used Ikea 12 X 16 Picture Frame for the side panel and this is for the top. Front is taped with clear plastic tape and top part is using letter size plastic sheet. ...even those cheap plastic sleeves...

The light on the p1p sucks and it is difficult to see anything, this light fixes that. Invert the STL in the slicer to print the mount for the opposite side. ...The mount is for this light...

This is a redesign of the Gridfinity Faceplate for Bambu P1P by Neebick on Printables: https://www.printables.com/model/399054-gridfinity-faceplate-for-bambu-lab-p1p After trying to attach that faceplate, I realized it wouldn't realistically be...

Puoi organizzare gli strumenti in modo efficiente e rimuovere solo ciò di cui hai bisogno.Design compatibile: Il toolbox è progettato specificamente per le stampanti P1S e P1P, garantendo una perfetta adattabilità. Puoi posizionarlo comodamente...

A simple Holder for up to 3 printplates for the P1P Pegboard enclosure.I like to hold everything together so i created this simple pegboard holder. 2 Parts a needed. ...Simply mirror the model on the z-axis to get the counterpart. Standing orientation...

With my Bambu Lab P1P, I have had problems with the buttons on the control panel from the beginning. It is mainly the arrow keys that are stuck or detected in the wrong direction. ...Therefore I have designed, printed and installed individual keys.Enjoy...

I wasn't wanting to enclose my entire P1P, just add some corner pieces for it to look nicer so I took the corner pieces from Hobo4ssassin's model and cut off the connector pegs that would attach to the side panels.

This is a stick on p1p poop shoot no magnets needed, I used one piece of double sided sticky tape, the stuff that comes in a roll and it held great, supports will be needed for the shelf print but not needed for base print. ...shelf sits down into base...

Parts required:x1 - PC4-m10Link: https://www.amazon.com/dp/B086W9HZDK/ref=cm_sw_r_as_gl_api_gl_i_7HK7H4847JY52G8NFFCM?linkCode=ml1&tag=morallygreyka-20x2 - #6-19 x 5/8Link:...