p mags 3d models

The file pmag has a deeper center hole that the file marked p-mag. This is a work in progress and needs a bit more refining but it's functional. It fits Pmag Ar-15 magazines and gives a nice standoff rest for the magazine. Enjoy! ... remixed from:...

Just supply your own spring and you're good to go. ... I plan on designing a printable, spring bending jig in the near future.

An anti-tilt polymer magazine follower for rifles prevents the ammunition from tilting inside the magazine, ensuring smooth and reliable feeding.

Just made a quick replacement for G&G magazines since one of my baseplates broke.

This holds one or two mags for a M&P bodyguard. The two mag holder is a little big(prints a lot). ... The single mag holder is small enough a shirt covers it nice(I have not printed it yet tho).

wip

This magazine space allows use of full size magazines in the Compact M&P 9C.  Printed in PLA  Layers:  .2mm Nozzle temp: 190*C Bed temp: 50*C Speed: 50-70 mm/sec Infill: 30% Supports: Yes

You need Tokyo marui ngrs M4 Magazine and D-day D-mag M4 30 / 130 rds magazine And you have to cut the TM ngrs magazine's wings and D-mag's rear part. ... Please refer to the picture.

You need Tokyo marui ngrs M4 Magazine and D-day D-mag M4 30 / 130 rds magazine And you have to cut the TM ngrs magazine's wings and D-mag's rear part. ... Please refer to the picture.

I knew that the CZ 75 magazines fit in the P-01 magwell, but I couldn't find any appropriately sized mag sleeves. Technically you can use them without a sleeve, but you risk bending the ejector pin from over-inserting if you slam in in too hard. I...

T.REX Arms sidecar pistol mag attachment for M&P 2.0 10mm. ...T.REX Arms does not make a holster for the M&P 10mm, but it does fit in my CZ P-07 holster, with a TLR-7, as retention is on the light.

It makes them longer so they're easier to get out of mag pouches and I found the factory ones had a rim on the base that pinched my hand. ... There are 5 files, one without a number and then four numbered one through four so you can keep track of your...

This is a magazine holder that I designed for installation at the core of my pickup's control panel. ... These units may be fabricated and secured to any surface utilizing three M adhesive strips.

I could not find a compact Glock magazine holder for a picatinny rail that I liked, so I made one. I designed it initially for my Kel-Tec sub 2000 so I can carry an extra magazine on the picatinny rail, and have it fold flat without needing to...

I could not find a compact Glock magazine holder for a picatinny rail that I liked, so I made one. I designed it initially for my Kel-Tec sub 2000 so I can carry an extra magazine on the picatinny rail, and have it fold flat without needing to...

I liked haakon1's design the best by far, but M&P mags are a little thinner than Glock mags, and I wear a 1.75 inch belt rather than the 1.5 inch belt his Glock mag pouches are designed for. Initially I imported his STLs into Blender and just...

This is for smith and wesson shield 9mm mags. Has enough retention for walking around and normal every day life. ...

Designed a custom airsoft magazine holster specifically for the ASG CZ p-09 and its detachable mount. The design is carefully crafted to be large enough to prevent gas release when inserting the magazine, yet narrow enough to keep it securely in...

Mag Loader for the 9mm M&P Shield Plus magazines. I took @Crashin_Machines' Shield loader and made it a bit thiccer. Enjoy! ... (I printed with a little support under the top bridge, 50% infill.)

This is a magazine base plate extension for a Smith and Wesson M&P Shield Plus. Other models I've seen don't fit because the tabs are facing the wrong way. This model has the inside tabs to fit the mag. ...There is a bumpy texture on the front to help...

This design fits over the standard magazine to provide better grip with all 3 fingers, but is less heavy and slightly easier to conceal than the extended mags. I personally also find it more comfortable than the extended mags as well. This design...

Crafted with precision using 3D Slash's advanced features.

Remixed the original design by chubbyzook. Recontoured to better match the original grip w/ plug to match.Use a M3x20mm screw to attach plug to extension. ... ***Make sure in slicer that plug is flat on the build surface*** Model that works...

Smith & Wesson M&P 12/15 round Mag Holster.

This is a remix of the M2.0 mag extension. I wanted something a little more ergonomic and OEM-looking. I've had issues with the rail lips sheering off when the magazine is dropped, but it works well if you baby it. ...I will try TPU down the road to see...

This is a magazine rack for the Smith & Wesson M&P 2.0 magazines. I have included 3 versions with different mounting options. One is mounted using (3) 25mm X 2mm Neodymium Magnets, one is mounted using round head screws, and one using double sided...

Smith Wesson M&P 12/15 round Double Mag Holster.

9mm mag for M&P Shield 2.0. No spring or mag follower. ...Mag fits into gun and is held in place good with only a small wiggle.

Grab onto the final notch on the 35-round magazine from Plinkertactical.com specifically designed to fit the M&P 15-22.