overlord dreammaker pro power connector guide 3d models

This is an upper filament guide that I designed for a Creality CR10S Pro V2 printer. It was designed for use with a 7mm x 22mm x 7mm bearing. The static upper guides all work great, but I wanted something to aesthetically match the lower filament...

I plug in my Thunderbolt display and power cord into my MacBook Pro every day, multiple times a day. This makes it faster and more convenient, also sparking interesting conversations at work. ... It should fit the standard Apple USB-C charging cable and...

This is an easy-to-use filament guide and measuring gauge for the Creality Ender-3 Pro (and possibly the Ender-3, let me know!). This guide ensures smooth filament entry into the extruder without bending, reducing the likelihood of breakages. The...

This is a Guide for the Palette 2 and Palette 2 Pro Filament. The input section on those devices features a significant design flaw that causes the filament to get stuck in a gap under the run-out detector switch during a run-out event if it's bent...

... go in, I had to remove a burr. If it's too snug for your tube, try rolling up some sandpaper, inserting it into the guide, and spinning it a few times depending on the grit. ... How I Designed This I used Autodesk Fusion 360 and FlashPrint slicer.

All ender series print bed magnet guide

Filament guide for direct drive extruder.

These little inserts click seamlessly into the guide tube slots on the back of the Flash Forge Creator Pro, enabling the guide tubes to protrude from the back of the printer and facilitate a more direct filament feed for non-indented hub spools that...

Made a funnel based filament guide for my CR10S Pro v2, but it should fit any printer using that same filament sensor. I needed this as I made a desk stand for the filament spool (can be seen in one of the picures) instead of using the standard...

This is a premium filament guide designed specifically for the Creality CR-10s Pro. It's engineered to prevent tangles by featuring a pivoting feed tube that adjusts its angle in real-time as the Z axis moves upwards. This innovative design ensures...

These little inserts fit into the guide tube slots on the back of the Flash Forge Creator Pro to allow the guide tubes to protrude from the back of the printer allowing non indented hub spools to have the filament fed more in line with the inner roll...

For those of you who purchased a Prusa i3 Pro B from eBay, I designed this filament guide and filter specifically to fit on the standard spool holder. With some creative thinking, it should be easy to adapt it to other spool holders as well. I'm...

A filament guide to help smooth the path of filament as it is pulled into the filament runout sensor on the CR-10S Pro V2. I reused several parts from the Ender 3 version (https://www.thingiverse.com/thing:3052488) but I have swapped out the bracket...

Filament Feed Offset for Flashforge Creator Pro: This attachment is designed to relocate the filament feed further away from the printer body, addressing a common issue where the filament can slip between the spool and the printer's frame, resulting...

If you Upgraded your Ender 3 Pro to Direct Drive you may want to attach a Filament Guide to your printer. Here's a simple solution. Note: The Hole where the FIlament goes through fits a Ø4mm PTFE Tube. Just put the Tube inside and cut it to your...

You can attach the guide with an M5x10 screw by either tapping threads into the holes or carefully turning the screw into the hole.\r\nA washer between the holder and the guide makes it easier to adjust the position of the guide.\r\n\r\nThis spool...

While Assembling it I discovered the guide components had an excessive amount of play in them and while utilizing it this resulted in a significant amount of noise and I encountered difficulty maintaining the exact angle required. I created these to...

Most filament guides for the CR10s Pro are push fit designs, but I've discovered that PLA loses its grip within a week or two in situations like this. So, I designed one that attaches using two of the existing screws from the printer's filament...

Side Mount sockets for the filament guide tubes on the Creator Pro 2. This allows use of separate filament holders (in my case passive dry boxes) placed next to the printer and makes changing filaments easier. This also shrinks the depth and allows...

This is a straightforward cable and Bowden tube guide I designed for my Ender 5 Pro. To avoid cluttering up my build area, I chose to route cables outside the frame wherever feasible since I'm building an enclosure around the frame. The hotend and...

The cutting mat guide for the Cameo 4 Pro needs slightly different dimensions. The parts for the "smaller" Cameo 4 models are wider. ... If the part should wobble due to different tolerances when printing with different printers, a small piece of...

This is a remix of Filboyt's v-channel end clip designed to mount a filament guide on an Ender 3 Pro. I really love this filament guide design - it's clean, stylish, simple, and perfectly placed to keep the filament feeding nicely. However, over...

MacBook Pro 15 Mid 2014 wall mount along with 85 watt power adapter.

A power supply holder that clips into the rails of the genmitsu 3020 pro

Straps are designed to expertly mount the MP Select Mini Pro power supply neatly.

Ender 3 Max/Pro Power Supply Cover that holds the USB and the hex keys

Simple power supply case for surface pro 4, it's a little bit bigger than original.

Secure the power cable on the Ender 3 Pro by clipping it into place.

An edit to brace a different style of power supply for the Genmitsu 3018 Pro

But if there was a filament snag, the connectors would snap or damage, needing replacement, and at the same time, the filament started cutting into the ring guide. I needed something better. a more stable connector, that was less prone to...