overhang test 3d models

Customized version of http://www.thingiverse.com/thing:58218 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58218 Instructions Using the following settings: Increment value is set to 10 Starting point is 45 degrees...

Customized version of http://www.thingiverse.com/thing:58218 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58218 Instructions Using the following settings: Increment to 10 units Starting at...

I don't understand your request.

Customized version of http://www.thingiverse.com/thing:58218 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=58218 Instructions Using the following settings: Font size is set to 90 percent. Box...

A tailored rendition of http://www.thingiverse.com/thing:58218 was created using the Customizer! You can customize it by visiting http://www.thingiverse.com/apps/customizer/run?thing_id=58218. To personalize your design, select from the following...

A personalized adaptation of the item accessible at http://www.thingiverse.com/thing:58218 was created using the Customizer app (http://www.thingiverse.com/apps/customizer/run?thing_id=58218). ... To do this, adjust the following parameters: - increment...

A lot of gauges and tests are readily available online, but I wanted to create my own as it better represents the challenges I faced with overhangs and stringing issues. ... I'm excited for you to try it out, so feel free to support my efforts by...

Print Settings Printer: FlashForge Creator Pro (Active Cooling) Rafts: Yes Supports: No Resolution: 0.1mm (or minimum layer height) Infill: 30% Notes: Don't even think about printing with supports, because this test is all about testing the limits...

Like the original, plus overhang print test and bridge print test

My printers can handle two out of four tests just fine, but two squares exhibit broken edges along the overhangs. Either it's the front two that are damaged or two on the sides, or possibly the two in the back - I'm not sure what's going on. I've...

This is an extreme stress test designed to push the limits of your 3D printing technology's ability to handle overhanging features.

So I designed a simple Test myself: Through the curvature of this model, the overhang gets slightly more steeper the higher it goes. I printed it in vase mode, so the seam doesn't influence it. The Arrow shows the "wind direction". Hypothesis: If...

This is a torture test that tests the overhang capabilities of your 3d printer. Print Settings Printer Brand: Monoprice Printer: Maker Select Rafts: No Supports: No Resolution: .2 Infill: any Category: 3D Printing

Humans embark on unaided endeavors.

Remix with 45-85 deg and 45-70 deg.

Here are some quick-print test models that I put together to help me calibrate my e-steps and test my support settings. the first is a simple 100x100x100mm frame for testing and calibrating all three axes. Print the model and measure each length to...

Here are some quick-print test models that I put together to help me calibrate my e-steps and test my support settings. the first is a simple 100x100x100mm frame for testing and calibrating all three axes. Print the model and measure each length to...

Overhang test with curves on the overhanging edge .stl - Ready to print.f3d - Editable Fusion 360 file

The Overhang Test and Bridge is designed to show how far a MakerBot 3D Printer can print at an angle before print surface quality changes. This test also demonstrates the maximum bridge distance a MakerBot Replicator can achieve without compromising...

Customized version of https://www.thingiverse.com/thing:3232756 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3232756

Just a thing to test overhang and bridging on all 4 sides

This testing tools consists of 6 different overhang angles: 15', 30', 50', 60', 70' and 80'... with a 50mm long bridging... I had tried 4 different PLA colours with 6 attempts... finally got 1 successful print... Surprisingly the 80' are barely...

This testing tools consists of 6 different overhang angles: 15', 30', 50', 60', 70' and 80'... with a 50mm long bridging... I had tried 4 different PLA colours with 6 attempts... finally got 1 successful print... Surprisingly the 80' are barely...

The test will utilize standard printing paper and focus on the gap sizes between printed characters. ... These gap sizes include: - Two millimeters - Four millimeters - Five millimeters - Six millimeters - Seven millimeters - Eight...

This test evaluates your 3D printer's capacity to print over gaps, enabling you to refine its settings for optimal performance in this area. ...Adjust the scale as needed to create a more or less demanding challenge, depending on your desired level of...

The Incline and Crossing test shows what angle a 3D Printer like MakerBot can produce without compromising print surface quality. This print also demonstrates how far a MakerBot Replicator can cross over obstacles without impacting print surface...

This is a rigorous test and demonstration print to assess the extreme limits of your printer's ability to manage overhangs. Each test features an explicitly labeled angle on its base, accompanied by a display stand designed to showcase the finished...