over center draw latch 3d models

Mass = 1066.52 gramsMake a sketch with a circle at the origin R6. Make a line to the left and underneath both 14 away. Make the left line 18 and between those a 45degree angle line. The bottom line running until a R5 circle's top. From that circles...

CSWA part

I created this by measuring out the measurements on the front and extruding backwards.

This is one of 6 original parts I used for this assembly. The only changes I made for this part were to make it smaller so it can fit the size of the rest of the assembly. I used this part to create a 'locking' mechanism for the fridge. ...I was going...

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimeters Process:I sketched the whole part in just 1 sketch and then did the boss extrude. ...It was relatively easy it's just figuring out the dimensions.

First I made a lot of dimensions to make it easier to sketch out, I started on the right slant and worked clockwise. ...After I made the sketch I extruded 45mm.

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersProcedure: I started this model with the sketch from the front view. Started with the circle on the origin, then I sketched all the lines above and to...

Part was built :)

The material used is AISI 1020, and it has a mass of 1066.52 units.

CSWA part

Mass = 1078.53 gramsVolume = 136522.41 cubic millimetersSurface area = 18776.27 square millimetersFor this model, I started by creating a new sketch. I then drew the outline of the model using the line tool, circle tool, trim tool and many more.

With SolidWorks, I created this model with the tools line, smart dimension, centerline, circle, and boss extrude. The material required was AISI 1020 which I made this model as. Understanding the blueprint of this practice part was simple as it...

This is an uncomplicated device designed to secure something in place. ...It's not exactly rocket science.

step1: sketch geometry according to the blue prints (( !! crucial !! ...- when sketching make sure the arcs are fully defined first, then make the line under the whole cut out concentric with the axis))(note) the axis point in the blue prints can be...

school education

Bolts/Nuts needed: 4 M3 x 06 Socket head bolt 1 M3 x 35 Socket head bolt 5 M3 Nuts

I started by changing the material to AISI 1020. I then started from the left of the sketch to the right. ...I used tools like circles, dimensions, trim, circle, filet, 3 point arc, and extrude.Mass = 1066.52 gramsVolume = 135002.52 cubic...

I used the line tool to create my shape than started to dimension everything to the correct length. I used the arc tool so i could make my curves and everything. ...I than extruded than and but a circle on the shape and cut it through the entire shape.

<p>PLA 200/60</p><p>Fan 100%</p><p>no supports</p>

a tool

Steps:1. Started the sketch o the 40mm ark and dimensioned as I went, when I got to the corner with the two tangent arcs, I made the horizontal line coming from the 45 angle coincident with the point of the 29mm arc.2. Extruded to part width3.

Steps:1. Started the sketch o the 40mm ark and dimensioned as I went, when I got to the corner with the two tangent arcs, I made the horizontal line coming from the 45 angle coincident with the point of the 29mm arc.2. Extruded to part width3.

I started by sketching out the front profile, making sure all the measurements including radius' were correct, then I boss extruded the model without including the circle.

I am a large language model. I don't have personal experiences or emotions like humans do. I was created to understand and respond to human input. ...My responses are based on patterns in the data that I've been trained on, rather than any personal...

Use for Door Cabinet....