ortur air assist 3d models

SummaryAir Assist Clamp and Cap for K40 Style 40W Chinese Blue and White CO2 Laser.Air assist clamp and cap designed specifically for K40 style lasers, ideal for a 40W Chinese blue and white CO2 laser.The clamp and cap are engineered to securely hold...

I remixed several parts so that I would have smoke assist while engraving, but also wanted air assist and smoke assist while cutting. This setup works well on my K40. The duct is sized for a 40x40mm fan. Assembled with four 3mm bolts and nuts and...

If you don't have a laser pointer, the air assist tube should be about 3 mm above your focal point of contact with the material. At the angle of the tube, the air is injected right at the point of laser contact in the groove. You'll find that you...

and since I wanted a simple and equally effective solution that is compact, I designed this Air Assist. Depending on the version, either 2 M2x8 or 2 M3x8 and 2 M2x12 or 2 M3x12 screws are needed ( whichever 4010 fan is used) to attach the fan and...

Carefully position the capped tube, secured firmly by clamp in place within the air assist mechanism, with the tapered end pointed at the calibration mark. ...Install and attach an easily sourced air source to complete this straightforward setup...

This is an air assist nozzle for the Longer Ray 5 Laser engraver. It accepts a 6mm outside diameter tube. Note: after installing this nozzle, you can no longer use the aluminium spacer to calibrate the laser. Instead, you have to measure from the...

brass tube for air assist tube 1 - 2 ft length of 4mm ID clear air tubing (and air pump of choice) 1 - m3 x 10 bolt and nut 1 - m6 drill tap 1 - 5/32 drill bit (9/64 is slightly smaller but could work for nozzle hole in length and side) Drill the .8...

An Air Assist Nozzle for the Stock Laser Head on the K40 Laser Cutter. The aim of the project was to design and build a lamar flow laser head to increase the cutting ability of the laser. ...Initial testing has not been started but if you print this...

Up for your printing pleasure is yet another air assist for the Chinese laser cutter. I've incorporated a boss for adding a 6 mm pneumatic elbow fitting, perfect for macro line applications. This design features a 5mm opening for effortless airflow.

I've tried various air assist nozzles on the market, but all of them have one major flaw: they interfere with a cross beam underneath the mounting bezel, making them unusable straight out of the box. So, I decided to design my own nozzle from...

This is an Air Assist Nozzle to be mounted at the TwoTrees Totem S Laser Engraver. It is used to provide airflow to the laser lens for protection and clearing smokes and fumes. The piece was designed to be screwed in with 4x M2.5 screws that use...

It is the new S9 model which has a black metal insert to create an air assist effect (poor) My S9 laser has a 19mm cavity that receives this insert. My piece should also fit the older S9 models if you have a 19mm cavity. The standard 4/6mm air...

So I decided it was time to start shopping around for a new supplier who might have better air assist systems in place. That's when I stumbled upon Epilog, and their setup really caught my eye. I figured I'd give it a shot, so I set out to recreate...

This is a set comprising of air assist nozzles with the following outlet diameters and clearance from the focus. This version has handy size labels embossed on the nozzles, a free version is also available on thingieverse without the embossing. :-)...

The air pressure is not just building up inside and goes wherever there's less pressure but directed outside. There's separation between the laser path and the air path inside. Make sure to set the focus BEFORE installing, as you won't be able to...

Side assist nozzle, to fit on an extension tube on a G8 Lense

This is Assist Mode activated on the Laser K40 system with a Nozzle Diameter of 26mm.

Using a larger fan (20x25mm outlet) and a 3D printed air cone dimensioned to suit the fan's flow and pressure capacity (air guide and outlet not being too narrow nor too wide) you get a good strong airflow. ...

Each of these nozzles has an intake for an 8mm air hose, which is then funneled into three channels blowing into the laser target area. This design results in a sufficiently high air velocity to keep the cut really clean. ... Note: Calibration of the...

... shows a slight improvement while using the laser to cut 2mm plywood. "Air assist2" has yet to be tested. Disclaimer: I do not know if the increased air resistance will damage the fan or overheat the laser diiode: use at your own discretion.

More to 3d themes: https://www.facebook.com/groups/3ddruckercommunityd Air Assist mod and honeycomb grid for the Atomstack A5 laser cutter The fan mod is used instead of two spacer sleeves for the controller board of the laser and inserted into the...

This is a remix I did, created a gap to allow for smoke egress. ...Modified the hose input so it is more vertical. Nozzle also 1mm shorter for a bit more air gap for smoke

Here is an alternative to an air pump to add an air assit to your S9 laser module, using a 5015 blower. You'll need to thread the two bottom front holes of your laser module to be able to screw the mounting system and the duct, with - 2 x M3x14...

I liked the design of this thing https://www.thingiverse.com/thing:4729176 but it didn't fit my laser module and I already had a standard air compressor for airbrushing so I pulled the barb off the end and replaced it with a .8 nozzle. The tubing...

You can add compressed air to the tank through a port to get faster responses from your system. The tank side fitting is 3/8 MNPT, and the air valve side fitting is 1/4 FNPT. You can use any standard 1/4-inch schrader or fill-style valve with this...

This is a remix of https://www.thingiverse.com/thing:4692711 I made this because the air nozzle was too high for my laser, I have reduced the height so the aim is where the beam focuses, 2mm below the shield.

This is a remix of https://www.thingiverse.com/thing:4692711 I made this because the air nozzle was too high for my laser, I have reduced the height so the aim is where the beam focuses, 2mm below the shield.

Sculpfun S9 Left Air AssistModified for efficient functional usage. This component has been used daily for 2-3 months without any issues. This was created to improve on currently available designs. Use of other open-source designs led to the...

Sculpfun S9 Left Air AssistModified for efficient functional usage. This component has been used daily for 2-3 months without any issues. This was created to improve on currently available designs. Use of other open-source designs led to the...

No need pricy air pumps. It is a 3D Printed Blower/Radial Fan Solution for Neje Laser Engraver Modules. Read Print Settings. ... Required Items; One of Neje Laser Modules A40640/A40630/N40630 1ea 40x20x12v Blower/Radial Fan 2ea DIN7985 2x20 M3 Bolts 2ea...