original prusa i3 mk2 3d models

It appears that you've provided a detailed assembly and configuration guide for an E3D Titan Aero extruder on a Prusa i3 MK2S printer. The instructions cover installing the motor, linear bearings, PINDA probe, heatsink fan, blower fan, and heater...

A filament guide that mounts on the top of a Prusa printer frame allowing it to guide the filament. InstractionPrint with support

... ...It's specifically suitable for use with the MK2/S system. To ensure proper installation, make sure that the combined height of the front rods falls within a narrow range: not more than 28.3mm and not less than 27mm, and they must remain parallel.

I wanted a larger LCD dial for my Prusa Mk2s, just like many others. As it turned out, I couldn't find one that fit my needs exactly, so I decided to design and build my own custom version. ...The result was a dial that is significantly higher and wider...

The original (see remixed section) worked great for a long time but the part that connects to the printer frame started to loosen up and eventually the spool holder fell off, spool and all. ... This model improves on the original design by adding a clip...

The original model worked flawlessly for an extended period but its weakest link, the part linking to the printer frame, started to deteriorate, ultimately causing the spool holder to dislodge, taking the spool with it. ...This revised design takes a...

In this remix, I flipped the mounting arm design over for added durability and strength. I also redesigned the entire mounting system to fit the GoPro perfectly, complete with a riser block that allows users to mount their camera at a higher angle.

The innovative design of this filament guide draws direct inspiration from the pioneering work of papinist on Thingiverse, a project specifically identified as thing #1764285. ...To ensure seamless compatibility with my own printer, however, I undertook...

Printer Camera Mount for Frame Attachment Below Heated Bed The Logitech 270/310 mount is a modified version of this file, engineered to fit snugly onto the arms due to its tight design. If your printer produces underextruded prints, you can further...

Small design PINDA protection.

We're about to tackle a crucial accessory that'll make your life easier, a simple yet effective tube to complete filament spool holder designed specifically with the Original Prusa i3 mk2 in mind. ...Head on over to thingiverse.com and check out this...

The original can be found at: http://www.thingiverse.com/thing:1668505 Print Settings Printer Brand: RepRap Printer: Original Prusa i3 MK2 Rafts: No Supports: Yes Resolution: 200 um Infill: 20 Notes: Printed in PETG. Added supports only to the camera...

These mounting supports are specifically designed to work seamlessly with the original Prusa i3 MK2 LCD cover. They grant you the flexibility to securely attach a RepRapDiscount Smart Controller directly to a flat surface, eliminating the need for...

... ID of the PVC pipe and modified the two arms for a secure fit around the 25mm OD. This design significantly outperforms the original i3 spool holder! Print Settings: Printer: ORIGINAL PRUSA I3 MK2 Rafts: No Supports: No Resolution: 0.2mm Infill: 10%

UPGRADED VERSION V2 Brackets with cross support for making a Double decker spool holder designed specifically for the original Prusa i3 MK2 Multi Material printer. 1. Print 3 sets of brackets. 2. Print 1 set of cross support brackets. 3. Replace...

Original Prusa i3 MK2 MMU It's the third iteration of Following extruder for MMU. Printing a large model takes over 18+ hours. I experienced multiple printing failures of large models whose height exceeds 180 mm. The cause of failure is excessive...

This is a redesigned Raspberry Pi Cam mount for the Original Prusa i3 mk2/2S/3 printer, reworked from scratch to attach directly to the y-carriage. No screws are required to secure it - friction does the trick. Meanwhile, I've also revamped the pi...

... **Print Settings:** * Printer Brand: RepRap * Printer Model: Original Prusa i3 MK2 * Rafts: No * Supports: No * Resolution: 0.20mm * Infill: 20% **Notes:** For this Hot-end part, ABS is the recommended material due to its superior heat resistance.

SPECIAL NOTE: This is a Multi-Material enabled STL, which I designed specifically for my Original Prusa I3 MK2/s MMU upgraded printer. It needs to be uploaded as a Multi-Material print so that words can be printed in the lid cavities. Each...

SPECIAL NOTE: This is a Multi-Material enabled STL, which I designed specifically for my Original Prusa I3 MK2/s MMU upgraded printer. It needs to be uploaded as a Multi-Material print so the words can be printed in the lid cavities. Each...

Printer: Original Prusa i3 MK2 Print Settings Rafts: No Supports: No Resolution: 0.2mm Infill: 20% Notes: The spool holders can be printed laying down without issues, but the filament guide is a bit tricky. The best position to print this part is...

THIS IS PART OF AN OVERALL Lack Enclosure design: https://www.thingiverse.com/thing:3129929 This is take two on the Original PRUSA i3 MK3/MK2.5 MMUv2 Backfeed situation for those that are having issues with alternate mounting as I was. This mount to...

When you've got your reels secured to the wall, a filament guide is just what you need! ...The upgraded model will also function seamlessly with the standard reel holder.

I've had no trouble getting my printer to roll smoothly - the spool doesn't tend to unwind any filament at all.

OPEN SOURCE USE AS IS.

I really like this thing and was looking for a way to make it more convenient for maintenance. To do so, I wanted to be able to slide the LCD display in and out while moving my printer. Print two brackets that attach to the underside of the surface...

OPEN SOURCE USE AS IS.

I upgraded my printer by adding 3 centimeters of height and a bit more width since I had some spare MakerBot filament on hand. ...The larger spools are definitely a welcome bonus!

We're not a brand or product. We are a Canadian Research Group (Open Source Engineering). STL Setting: MM Share us your printed one. ... Send your revision or bug to: research@gueritech.com research@gueritech.com donate@gueritech.com ...