orbiter extruder ender 3 3d models

Ben https://www.thingiverse.com/thing:4748675 Orbiter v1.5 https://www.thingiverse.com/thing:4725897 Ender6 is set with orbiter v1.5 1、Adjust the e-axis driving voltage of the main board to 0.3 ~ 0.6V 2、Use S3D send G command：M92 E655 M500（E:x |...

This is the Direct Extruder part I designed for the Ender 3 V2, it requires you to disassemble and reassemble the Extruder stepper motor and Bowden extruder into a Direct Drive Extruder. Optimized the structure, and designed the heat dissipation...

Creality Ender 3 Extruder Knob A handy knob, appropriately sized, allowing you to move the filament easily! A very snug fit onto the extruder shaft to provide a firm fit. It may need some force to put on the first time. Check out my other upgrade...

This design caters specifically to the ender 3 extruder arm extension, making it easier to reach and manage. It's tailored for armv2 and comes with some specific instructions: Measure carefully because this part was designed to fit snugly onto the...

This prevents the filament on the ender 3 cutting a line in its plastic extruder. Uses the bolts on the brass z-axis rod holder. Don´t over tight it as it can result of your z screw rod to not rotate.</p> <p>Open slot for easier filament replacement....

Created this for people that have converted to a direct drive on the Ender 3. Since were the extruder was is now empty I thought it would be a good place for a Raspberry Pi camera for OctoPrint. Used...

I made this quick fix to stop the filament from wearing out the hole in the clamping arm on my Ender 3's extruder. Now, you just need to swap out a bit of tubing and that's one less useless fitting from Creality that comes with the printer gone. It...

This is a voron Printhead that is attached to a Orbiter and this is allowed to be placed on an Ender 3 / Ender 3 Pro / cr-10 Materials needed x8 M3x25 Screws x10 M2x8 Screws x2 40mm x 40mm x 10mm 24v side blower fan 40mm x 40mm x 20mm 12v noctua fan...

This is an extruder plate extension for the Ender-3, designed to move the extruder further to the center of the x-axis. With the V1 mount, I shortened the bowden tube by approximately 6cm. The V3 mount allowed me to remove an additional 2cm. Uses...

Specifically engineered to optimize the Ender 3 3D printer's capabilities by incorporating these key features: * A robust 3:1 gear ratio * A threaded hobbed gear for improved filament management * Adjustable spring tension for precise control * A...

Just another tweak to fine-tune the precision of the Ender 3's control system.

I have been using my Ender 3 for quite some time now and was on the hunt for a fresh extruder design. I needed something that would both look great and offer direct drive functionality. The Prusa extruder design really caught my eye, so I went ahead...

\r\n• 5cm or more of PTFE tube (bowden tubing).\r\nThe existing parts (spring, guide wheel, and screws) from the original Ender 3 extruder will be reused.\r\n\r\nThis re-designed Extruder consists of both the base and lever arm, which must be used...

The Ender 3's G-Code is stored on a tiny SD card nestled within its robust metal frame, waiting to be unleashed by a skilled operator's deft hand. A series of expertly crafted knobs and levers surrounds the printer's central axis, each one poised to...

This knob for the hobbed gear and stepper on the Ender 3 simplifies priming of the extruder by eliminating the need to control the stepper through the printer's interface. The part should work with all printers featuring a 5.5mm diameter stepper on...

Printer enthusiasts rejoice, as we delve into the world of precision adjustments with the humble extruder knob, a crucial component on the Ender 3 and CR-10. This small yet mighty tool holds the key to unlocking perfect prints, and for many, it's a...

This is a re-designed version of the original Extruder which came with my Creality Ender 3 printer, with the following design goals.1] Tighter filament path constraints, to enable printing with TPE90A (a flexible filament)2] Adds more clearance...

This is a re-designed version of the original Extruder which came with my Creality Ender 3 printer, with the following design goals.1] Tighter filament path constraints, to enable printing with TPE90A (a flexible filament)2] Adds more clearance...

I designed a one-of-a-kind Extruder knob for my Ender 3 with a tiny baby Groot perched on top. I also created a Rocket Raccoon design that will sit proudly on my z rod - more on that later once it's printed. Key specs: * Material: 16g * Estimated...

I watched this fix for slipping Ender extruders, the file did not download. Here is my version , just slip it behind the spring. ...4 options in thickness from .5 to 2mm https://www.youtube.com/watch?v=k5Zl2NJpbsg&t=124s

I began by utilizing a different Thingiverse Ender 3 extruder filament guide that I downloaded from https://www.thingiverse.com/thing:3010366. It functioned properly, but it merely pushed forward without any specific alignment capabilities and failed...

This Ender 3 modification will transform your printer into a more streamlined machine, reducing its overall width while enhancing extrusion performance by pulling filament in a straight line from spool to extruder. As a result, filament no longer...

The fan support is slightly offset towards the front of the printer because depending on the age of the ender 3 the screws of the belt tensioner are not of the same thickness so the support comes forced on it during large printing. The ring was...

I've seen many people dissatisfied with the spring tension on their Ender 3's extruder. To alleviate this issue, some users have opted to stretch the spring, but I prefer a simpler approach. All you need to do is print an adapter, remove the spring,...

This is a straightforward conversion to a direct drive extruder on Ender 3. It features a holder for a stepper motor and a dual filament feeder. For reference, see the link:...

THE MOST CURRENT IS LOCATED HERE: https://www.thingiverse.com/thing:3965880 A NEW AND IMPROVED SET OF PARTS TO ADD THE TITAN GEARED EXTRUDER TO THE ENDER 3. I DESIGNED THIS AROUND THE TRIANGLE LABS "TITAN" EXTRuder (USING THE BOWDEN TUBE ADAPTER...

A modified Fallout-inspired turret designed specifically for the Ender 3 printer. ...The original model proved too large, often spinning uncontrollably on the Z-axis.

<p>It works. ...I switched back to Bowden drive, because Bowden drive is better on a stock Ender 3 pro (circa 2022)

I've secured my Ender 3's hot end wiring with a custom-made cable clip, which provides a snug fit and prevents loose connections.

Remix from original by techboner. ...Made it so it fits Creality Ender 3 V2 (original was to small). ...Might fit others.