orangerx open lrs 433mhz 3d models

Case for project from a post on WordPress at techniczny.wordpress.com dated 8/10/2016 titled "Radio Control in an Intelligent Home".

JR module replacement cover & Antenna relocation for the OrangeRX DSM2/DSMX/DEVO Version with the screws on the bottom. To-Do: print Top-Part print Middle-Part print 2x Pin Assembling: push the two pins into the top-part (tight fit) add some glue...

Terminal cover for MeanWell LRS-75 power supply. This one actually fits the LRS-75. ... Print it as in the .stl, the small overhang doesn't need support.

Meanwell LRS-350-24 power supply cover with mounting for a IEC C14 connector!

Openbuilds PowerCase with Meanwell LRS-350 Power Supplyhttps://openbuildspartstore.com/powercase-kit/Rough Model,

Case for Mean Well LRS-50. Lid clicks on to the case. ...

Staggered PSU Mounts designed to fit Meanwell LRS 600 power supplies

Surface Mount for the LRS 350 Power Supply. ... 1/4 inch-20 hole

Surface Mount for the LRS 350 Power Supply. ... 1/4 inch-20 hole

Qty 2 M3 heat set inserts are used to mount the socket, I used McMaster Part # 94180A331.More information for 3D printing and 3D printable files can be found here:https://www.thingiverse.com/thing:6068969Credit to the following users for their models...

This unit is engineered to secure an LRS power supply upright within a Harbor Freight ammunition container.

People are making a custom cover that fits snugly over the Meanwell LRS-50-5 power supply unit, or other Meanwell PSU models of similar size to the LRS-50-5, which can be found at http://www.mouser.com/ds/2/260/lrs-50-spec-752940.pdf.

To mount the cover to the power supply, the following non-3D printed parts are required: M4 x 8 socket head cap screw - qty: 2 M3 x 10 flat head cap screw - qty: 2 M3 Heat set insert - qty: 2 These are the M3 heat set inserts I used:...

I upgraded my setup by swapping out the broken antenna for a versatile SMA connector, allowing me to hook up bigger antennas with ease. ...This nifty conversion seals the antenna hole and gives solid support to the new attachment.

Measurements from Killer_Angel's mount can be found in case by j0Bro. The case and arms are remarkably slender to minimize weight, making them potentially unsuitable for printing with brittle filaments. For the top cover, refer to j0Bro's thing on...

The Mean Well LRS-350 power supply, with diverse voltage options like LRS-350-24 (24V) and LRS-350-12 (12V), is a favorite among 3D printer builders. This particular model is an enhancement of Adam Filipowicz's original design, featuring improved...

Brackets for 4x Meanwell LRS power supplies. Screws required are M4. I specifically used M4x10mm with this configuration. ... Terminal covers are here: https://www.thingiverse.com/thing:4961921

Mean Well LRS-350 Power Supply Module - 35W 3.5" Single Output PSU - 24VDC, 1.47A, 85% Efficiency, with Built-in Short Circuit Protection and Over-Temperature Protection.

This is a PSU cover for the Meanwell LRS-75-5.You need a M3x6 screw to mount it.

I upgraded my power supply unit to a Meanwell LRS-350 and tailored the existing mounting system to perfectly accommodate it.

I created a safety bracket for the Meanwell LRS-150-48 PSU which protects the power terminals from being touched by mistake.

This is a box for QLRS enthusiasts. ...To learn more, visit my blog at http://qczek.beyondrc.com/qczek-lrs-meets-taranis-x-lite/.

Needed a housing for my Meanwell LRS-100 PSU to mount under my IKEA Lack table enclosure so quickly made this one up in FreeCAD. ...

A cover for Mean Well LRS series power supplies. ...Print Settings Printer: Wanhao Duplicator i3 Rafts: No Supports: No Resolution: 0.2 Infill: 85% Category: Electronics

A protective housing for Mean Well LRS series power supplies is provided. ... Print Settings Printer: Wanhao Duplicator i3 Rafts: Yes ...

The body is made of a PLA material that contains 25% filler. ...The cover fits the Expert LRS 8CH v5.0.

Fixing apparatus to 2020 profile for Meanwell LRS-350-12 model psu. While designing, it was ensured that air flow was not interrupted. lrs-350-12 mount_1 file may need support to fan side. Use M4x6 screw for fixing the psu with parts. ...You can use...

A simple desk enclosure for the well known RIDEN RD60xx range of DC-DC power supply controllers AND a Meanwell LRS-100 power supply Google the power receptable https://www.google.com/search?q=IEC+320+C14+male+panel+mount Google Riden power supply:...

Enclosed Terminal for Safety Reasoning: Mean Well LRS-350-12 & LRS-350-24

Made a safety hood for the MEAN WELL LRS-350-24, it may or may not fit other Mean Well PSU's. Good luck. ... Step file included in case you want to make modifications.