orange pi 5 case 3d models

Orange pi 5 case, everything is kept accessible, be careful, it's a snug fit

STL and STEP files are included here and the complete source code is available under the GPL 2.0 license at https://codeberg.org/combolek/cad/src/branch/main/orange-pi-5-case. The case was designed in CadQuery 2. I tried to make it so it's easy to...

This is my spin on Orange Pi 5 Case that is designed with 2280 SSD in mind and a 5015 radial fan for cooling. The piece of painters tape is used as a air duct to increase airflow above SOC. To mount fan I used countersunk m3x20 and nuts (barely...

This is a remix of an existing case (https://www.printables.com/model/359018-orange-pi-5-case). ...It adds M.2 access, a power button, a 4010 fan with 6mm heatsink and easier SD access.

This is a case for the new Orange Pi 5. There are 2 different cases, and 2 lids to choose from. A case with the GPIO and LCD connector holes, and one without those. There is a lid with a fan holder for the CanaKit 30mmx7.5mm Fan used on Raspberry...

This case is designed for use with orange pi 5, but it can be used with other computers of similar sizes.For assembly, you will need screws of a suitable size of 4 M2.Attention, the inner part has a specially enlarged size since I used a soft...

Orange Pi 5 Case 50MM fan

pc case for orange pi 5

You need M3 - 4 screws PC fan screws - 8pcs

This case fits an Orange Pi 5 with an 2280 nvme ssd. All slots (SD,USB etc) and power/reset button are accessible. Requires 5x M3x10mm screws. Use a well calibrated printer as it is a tight fit. ...

This is a remix of the model here: https://www.printables.com/model/646840-orange-pi-5-plus-case-with-40mm-x-10mm-fanI was not able to get laser cut acrylic plates for the whole sides and I did not want to close them off entirely. ...Hence, I removed a...

I designed this case for a couple of reasons the first being that all of the other cases for the orange pi 5 plus that I found felt and printed very thin and with my printer using a 0.6mm nozzle I often ended up with weak walls. So the walls of this...

BOM: * at least M3x20 or bigger x 4 (optional) * transparent filament for indicator (optional) TODO: * Replace heatsink(bigger) and cooler(60x60x10 5V) - higher Top part * Smaller bottom part for those, who are not using NVMe, or using NVMe without...

... grabs the TV to the wall. ...The base is taken from this TV support https://www.thingiverse.com/thing:4461630 And I got the measures to place this case https://www.thingiverse.com/thing:5761356 . ... Excuse me if you see any error, I do not design.

Nothing special, I printed using Standard PLA on cool plate.

Made remix for a fellow redditor. Not tested, but ready to do some adjustment if needed. ... Feet adapted for 13mm dia rubber disks, you need to mirror them 2/4 parts

But the only thing I plan to update currently is a different bottom with more room around the SATA connector for the (optional) 2.5" drive, at the expense of some protection on that edge.    The Orange Pi 5 board is supported by these protrusions. I...

))))This is an V3 of my Orange Pi 5 case to run PhotonVision for an FRC robot (V1 is now hidden from the public because it's an abomination). I didn't include mounts for an LED ring, since it seems that FRC has fully phased out their reflective tape...

Recently purchased an Orange Pi 5 Plus and needed a case for it. Here's my 1st crack at it. ... <a rel="nofollow ugc" href="https://ko-fi.com/john_u"><img src="https://i.imgur.com/KjJjavu.jpeg" alt="Buy Me a Coffee at ko-fi.com" title="Buy Me a Coffee...

For now it should fit an Orange Pi 5 board, an SSD in the bottom (why waste an NVME drive on this board when it caps it at 500 mb/s?) and a 40x20 fan in the back all in one case. ...The case should also have enough room internally for a good heat sink...

This is my second case for the Orange Pi 5 Plus. The vents on the side pieces are a bit ambitious and resulted in some curved overhangs. They wont print cleanly, but I have oriented the part to print upside down so any messiness will be located on...

Really great design, especially I like that it allows installing an M.2 drive with a radiator and a single fan, providing airflow to both the CPU and M.2 drive at once.I tried using the author's case side, and it works well, but I prefer the mesh...

Classic Xopi case for Orange PI 5

I wanted a simple case for my Orange Pi 5 board that allowed access to all ports, so I designed this case to just snap together. A 3cm 5V fan should be able to fit in with just pressure, but I provided M3 holes if you want to screw the fan in. The...

N64 based case for the Orange pi 5 board.

upper.dxf and lower.dxf are the laser cut files with 1mm board 30mm*30mm fan

You'll need: * 4 USB extensions (with soldering tools) to keep it compact * A female RJ45 connector and about 10 cm of ethernet cable with a male end * 4 screws for the opi * 4 floppy screws for the 2.5 hdd * I use a molex to sata extender to create...

Orange Pi PC Stack-Able Rack for Supercomputer Modeling. This project is a testament to the creativity and ingenuity of its maker, who brought it to life using Tinkercad. ...The design can be edited online at...

Cluster Case Designed for Speedy Assembly and Compact Cluster Construction Features Cross Flow Vents, Key Components of an Innovative Design Created Using Tinkercad's Powerful Tools to Build Online at https://www.tinkercad.com/things/c89D0qoEPOR