openastrotracker 3d models

************************************************************************************** Initial: I designed this tripod for the OpenAstroTracker with the AutoPA addons. I have tested successfully this tripod with 9kg on it. I recommand to test it...

This is a focuser for use with the OpenAstroTracker - allowing you to focus your camera lens remotely from the controller or controller attached computer (the lens & camera will be set to manual focus, and this assembly will allow adjustments...

Custom Belt Tensioner for Improved OpenAstroTracker Performance

Case for Electronic Components of OpenAstroTracker Found Here: https://www.thingiverse.com/thing:4167783 A Larger Version of https://www.thingiverse.com/thing:4223944 Designed to Fit MEGA Has Been Created This Design Is an Enlarged Version of the...

... accessories, one of which is the PoleMaster Mount. ...This innovative mount was specifically developed to integrate seamlessly with the OpenAstroTracker, offering users an unparalleled level of control and precision when it comes to astrophotography.

This clamp can be used to fix the OpenAstroTracker mount. If you have mounted a camera the mount starts moving around depending on the weight. ...This clamp holds it in a fixed position.

Case for OpenAstroTracker Electronic Components Room Provided for HC-06 BT Module Installation JST-SM Connectors Used - Available at Amazon UK (https://www.amazon.co.uk/dp/B0716JMHNJ/) Crimping Required for JST-SM Connectors - Banggood Link for...

The design is a remix of https://github.com/OpenAstroTech/OpenAstroTracker-Addons/blob/master/DigitalLevel/CAD/Digital%20Level%20Holder%20v7.f3d Magnetometer is...

A simple cable hold-down/tie-down for the OpenAstroTracker AutoPA base. I used this to help route my Azimuth motor wires back to my controller box. They utilize the same #8 screws that mount the AutoPA base down to your platform of choice and have...

This is a power supply box for the OpenAstroTracker project. ...An input power supply between 12vcc and 28vcc is provided through the "input" barrel jack, and the right voltages are provided to power: - DSLR (8mm barrel jack) - Arduino Mega (8mm...

I could print all parts of the OpenAstroTracker except for sections 6a and 6c of the split ring. Owning a Rostock Max circular bed printer, I encountered an issue since there's no diagonal to utilize in order to fit the print, unlike a rectangular...

I created this mount specifically to utilize my Telrad with the OpenAstroTracker (https://www.thingiverse.com/thing:4167783). It takes advantage of the mounts for the guidescope (https://www.thingiverse.com/thing:4181640) without requiring any...

I designed this thing to integrate the NEO-6M GPS module in a deported way from the MKS Gen L in the OpenAstroTracker. The GPS antena is consequently as far as possible from the motors and without obstacle overhead. ... This thing allows to maintain...

The original can be found here:https://www.prusaprinters.org/prints/137723-openastrotracker-controller-enclosureThis version has added ventilation holes for better airflow to the stepper drivers, an additional GX12 hole so up to 6 can be mounted now,...

This allow to disconnect the LCD from the motherboard of the OpenAstroTracker for transportation / storage. I have to remove the RESET button (not very useful on this box for me) because the VGA cable used has only 9 wires instead of 10. I have...

Case for the electronic components of the OpenAstroTracker https://www.thingiverse.com/thing:4167783 Enlarged version of https://www.thingiverse.com/thing:4223944 to fit the MEGA I have not printed this, so let me know if there are issues. Print...

Case for the electronic components of the OpenAstroTracker (https://www.thingiverse.com/thing:4167783) Has room to place the HC-06 BT Module. Connectors are JST-SMs - I used these: https://www.amazon.co.uk/dp/B0716JMHNJ/ Connectors need to be...

This is 2 versions of the Alt Track component of the AutoPA addon for the OpenAstroTracker. In my opinion, there is a potential problem with the AutoPA base not allowing sufficient range of motion. Specifically, the track only really allows for...

(box11 files) This simple box contains the basic electronics required to run the OpenAstroTracker https://www.thingiverse.com/thing:4167783 Designed to hold the Arduino Mega (or Uno), LCD shield, 2 stepper motor drivers and a buck board, it also has...

An addon for the OpenAstroTracker. The current splitring uses M3 bolts directly pressing onto the drive belt. This is not good for the belt if you slacken/tighten the belt between uses as it can easily punch a hole in the belt if done too tight. ...

My version of a box for the OpenAstroTracker electronics, NEMA17. All the electronics are in one main box with a small connector box mounted on the OAT itself. The two are connected with rj45 patch cable / keystones. Note that this is probably...

This is an enclosure to house all of the required electronics modules for the OpenAstroTracker controller.https://wiki.openastrotech.comIt has standoffs and cut outs for the following:1 x MKS Gen L v2.1 Controller Board with 5 x TMC2209 stepper...

M14 thumbscrew with round end for the OpenAstroTracker. ...60 mm long although the useable length is a little less.

I make this thing to adapt a 60mm bubble level to the AutoPA addon of the OpenAstroTracker.

I adapted the OpenAstroTracker camera mounts to use M3x30mm screws, replacing the standard M2x30mm screws. ...I've also attached the revised STL and STEP files for your reference.

This is another laserpointer holder which I have designed for my OpenAstroTracker mount. It attacheds to the top of the alu profile. ...It fits quite neatly and should work better compared to my previous designs.

This is a hall sensor and magnet (d = 6 mm) holder for the openastrotracker. The sensor is slid into the holder and should fit very tightly. No screwing is necessary. The magnet holder fitted best on my ender 3 V2 at 103%. ...It is screwed to the...

This is a replacement RA motor mount for a NEMA 17 stepper with harmonic drive gearbox for the OpenAstroTracker (https://www.thingiverse.com/thing:4167783) You will need the following parts: * Harmonic Stepper X17-34-30A * 8 pcs. ...DIN 912 M4x10 screws...

I designed this thing to hang a USB hub to the OpenAstroTracker with the AutoPA add-ons. ... Needs for assembly: - 2 screws M4x40mm to replace the original screw of the AutoPA add-ons The USB hub can be provided here:...

I designed this thing to make easy the power connectivity of the OpenAstroTracker with the AutoPA add-ons. Actually, the original MKS Gen L box placed inside the base frame doesn't allow the use of the power supply plug with this last. ... The plug...