open scad 3d models

1º You will need to connect a rf-nano to the USB in your computer, install the proper driver so it is recognized as a COMxx Serial Port, Open the Arduino IDE, Select the right COM port, the right Arduino Board type, and also the right...

S4 Avant Lighted LogoThis was a design I created as a retirement gift one of my best friends (lovingly nick named The Douche, no seriously, lovingly).  He had recently purchased an S4 Avant so I found this to be a fitting tribute to the...

All of the unnamable, unfathomable endless universes constantly branching as Hugh Everett described in the mid 1950's. This is the place where gods are created.The Original Galindos -...

Neither can the Quistavera (though it would never be admitted).Always in the background, created by forces unseen, they go about the shadows and dark passageways of the Quistavera where few dare tread. Add some to your growing forces today!The...

The chain section containing the opened bead should be placed between the two adapters. Then the adapters were pressed together with the pliers. In comments (answer for ADBZA) you can find additional info how to use them, and now (18.09.21) I upload...

This will now take out the slack in the fitting compared to only push in the tube.Issues and fixes:IssueReason (possible)FixPictureBed belt is wearing off at the topfront idler pulley is bent backwardsUse a lagre set of pliers to bend the pulley...

These pins do not come in STL files but can be made out of short pieces of regular 1.75mm filament;- Batmobile can be mounted on a cylinder for smooth and quick rotation or assembled with a cap;Suspension:- The active suspension of the model's front...

The intention was to let the camera tilt slightly with the hinge bracket while the top cover is opened. It is done due to friction of the hinge rod. It is able to tilt 22 degrees up and down. LCD config for Raspbian and Kali: Add...

That clip should be on the outside, i.e., nearest the frame.The front pulleys do not need grub screws.The 20T pulleys will not fit through the openings in the brackets so the shaft, bearings, spacer, washer and pulley have to be assembled by sliding...

The alien’s exaggerated eyes are full of hatred and its toothy jaws are open in a crazy laugh. The author of the model made sure to pay careful attention to every little detail and extraterrestrial texture of the model, so we urge you to take a...

If do you need to get the lock back off, the best way I found was to stick long allen keys into both of the lock's holes and then pinch them together to lever the lock slightly apart, which reduces the pressure enough that you can wedge a thin...

---- **Remix Sources** The snowflakes were created with the The Snowflake Machine by mathgrrl and the inspiration for this thing came from seeing the Christmas ornament with Name - Names pack by RobertPoland ---- ###Some of My Designs Click an image...

(That's something else, sorry.)Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

2mm was used to stretch the panel because a gap was created when the panel was actually made to the exact size on the CAD.正面の扉は印刷部品で枠を作って嵌め込んでいるので、これもパネルの加工は不要です。CAD上でピッタリのサイズにすると、実際に作った時に隙間が生じたので2mm伸ばしています。The doors could not be made to open both...

The inner strip might need to be opened and realigned.Led assembly, top channel does not attach to the top, but the base walls.The led data channels should probably have a resistor in series to protect the led's. Places like Adafruit and Sparkfun...

The inner strip might need to be opened and realigned.Led assembly, top channel does not attach to the top, but the base walls.The led data channels should probably have a resistor in series to protect the led's. Places like Adafruit and Sparkfun...

18a) Attach a 40mm 12v fan to the top section so that the "open" side of the fan blades faces outwards. Connect the + and - of the fan either to the PSU (could use the ramps power connector as long as you can get a good connection with 2 cables in...

You can open the gcode file in a text editor to find out the order of the colours though!In the gcode, search for "M600". The first entry you'll find is "M600 T0", which is the prompt for loading filament colour 1 at the very start of the print (it's...

What surprised me is that the design not only works well for sails, but also opens up completely new design possibilities. Just look at this and let your creativity run wild:</p><figure class="image image_resized" style="width:50.67%;"><img...

Minimum Build ------------------- At the very least, you need the following parts: * 1x 4-Way_Planting_Module_Hollow_Twist.STL * 1x Dispenser_Module_Internal.STL * 1x Filling_Cap.STL * 1x Filling_Cap_Symbol.STL * 3x IKEA_Muskot_24cm_Petal.STL * 1x...

(new board)Use double-sided tape to attach the charging board to the hull.Solder all cables on the motor controller board then protect it with heat shrink tube(16mm) or electrical tape.Assemble the left chassis and insert the motor and zip...

Open it up in a text editor and find this block near the start that sets the initial temperatures:M104 S230 ; set extruder temp&nbsp;M140 S85 ; set bed temp&nbsp;M190 S85 ; wait for bed temp&nbsp;M109 S230 ; wait for extruder temp&nbsp;Replace that...

However lofigenerator.com is not open source, so I can't redistribute my version of that project.I am sharing the patches I made to various projects to get that working on the Pi, though:Fix a crash in node-speaker when a write to the speaker didn't...

Since its early days, Chevrolet has been synonymous with Muscle Cars that pack a punch on the open road. The iconic Camaro is one such model that embodies the very essence of what makes a Muscle Car great - raw power, precision handling, and a deep...

Open Serial Monitor. In the command line, we enter our coefficient with a dot as a separator. As I mentioned above, in the my case of coefficient = 7.7038. After the keyboard Enter - the entered coefficient will be displayed and saved in the...

Scientists from computing centers that would evolve into supercomputing centers and then a network open to the world, even our phones, televisions, and watches. By late 1968 ARPA awarded an RFQ to build a network to a his former employer, Bolt...

If you have any tips: I'm open to suggestions and improvements and will try to implement them. So far, I haven't been able to print it in 3D or split the STL parts into individual pieces. This tank robot was made with Tinkercad. Check it out online...

Instead, you print a mount for your chosen extruder and hotend that install with just four screws meaning you can quickly swap to another extruder and hotend while still using the same carriage, improved maintenance.Hotend fan upgraded from 4010 to...