open rhombic d12 3d models

Here are instructions on how to make this D12 https://www.instructables.com/CAD-a-D12/

tis is my side exit exhaust for the WLP D12

The prototype of Zdolshin lacked substance, necessitating a sturdy D12.

Pivot bearing d12...15 GOST 3635-78 (ISO-6124-82)

A storage box with the shape of a d12. The hole can fit 6mmx1mm magnets. Print instructionsprint it with the opening on the bed. Migth need some supports for the lower numbers.

Reefer Box with Openable Doors. ...Designed to fit WPL D12 RC Truck 1/10 scale. ...You need: 4pcs M2X10 screws for the hinges 2pcs M2X10 for Bar Mount (or can use glue) 4pcs M3X6 for Mudguard (or can use glue) Original screw for mount to Main Chassis

you will also need M3x6 mm bolts M3 square nuts LED strips of your choice power supply and the skills to do the Electronics (soldering and such) a bit about the Rhombic dodecahedron: The Rhombic dodecahedron is perfectly stackable leading to an...

I have integrated a 3D printable "cooler" blower into my Rhombic Stirling Engine blueprint, which features slight modifications compared to other designs. The addition of this blower requires certain changes in the design. It would be great if...

I decided to create a spot to stash my apple pencil on my desk when not in use, so I rapidly assembled a rhombic dodecahedron using Fusion360 and carved out a profile at the top to cradle the pencil. ... I've also included the solid model if anyone...

Set the height, h, to 1 for a rhombic dodecahedron. Check out this article for more information on Cartesian coordinates and dodecahedrons: https://en.wikipedia.org/wiki/Dodecahedron#Cartesian_coordinates Here's where I printed my dodecahedron: -...

This is fan duct for replace original on Wanhao D12 and add more airflow.

this is a ducktail for our WL D12 Check my profile for more rc parts

The original of Zdolshin was hollow but i needed a solid D12.

This is a Truck guardrail for WPL D12. ... Hope you like it.

Reservoir pour WPL D12, s'installe a la place de la batterie sous la benne

WPL D12 front hub printed on ender 3 printed with raft printed at 100% infill

here i made asimple d12 pot without drainage :D Feel free to remix

Custom D12 for Valnya Ruleset Discord Server: Join Now at discord.gg/mpRXK27

Roof air intake for WPL D12. ...Just print and glue it.

This is fan duct for replace original on Wanhao D12 and add more airflow.

A replacement part for the D12 chassis's lower arm mount for the independent front suspension.

I could not find a d12 bullet die, so I remixed one.

Un tiroir pour glisser sous le plateau de la Wanhao D12/230.

Just my design of an Insert to allow different seats to be fitted into a D12.

This is a flat bed to replace the tray on the WPL D12.

tray handle for wanhao d12-230 model taken from the ender3 with added wanhao logo

This model prints flat, then folds along the edges to form a rhombic dodecahedron. The inner sides snap together, as shown in the video below, to hold the shape without additional connectors. If you change filament mid-print, you will have a...

... both but I needed to trim down the connectors to clear the tray. Also has an open rear to a allow longer battery if the existing tray is trimmed. ... Fits the WPL 1500mAh battery but I've found it's too thick to swap out through the battery door.

This is a knuckle for WPL d12 Print in mirror for 2nd one Modified to fit stock d12 bearings and front axle modified to fit M3 balls original part in this file https://www.thingiverse.com/thing:4272388

A dodecahedron (D12) with musical note names on each face. ... Uses actual sharp {♯) and flat (♭) instead of (#) and (b).