oneup pump mount 3d models

Last winter, the water pump in my camping van busted because of some left over water in it. After a friend of mine got a resin printer, I sat down and designed this replace part. The part has been tested (not over a long peroid!) and it works fine. ... ...

I decided to make a bracket to keep it as such. The case already had holes drilled to keep it in a horizontal orientation, so it was a matter of making a small plate with the holes in the right space (50mm distance between them) and making a panel...

Last winter, the water pump in my camping van busted because of some left over water in it. After a friend of mine got a resin printer, I sat down and designed this replace part. ... The part has been tested (not over a long peroid!) and it works...

So, I designed a clamp that attaches the pump to the handle, followed by a Schrader valve connected to a 3/8" hose barb, and then a 3/8" hose barb linked to a threaded connection on the drink tank cap. A groove for an O-ring was incorporated into...

Exactly the same mount as the source but it fits 3030 extrusion instead of 2020 extrusion.

Cradle mount for the controller on a Reefbreeders RPM. I believe its a V1. ...One with a digital output.

It perfectly accommodates a GoControl Z-Wave open/close door or window switch to fit snugly onto my sump pump discharge pipe. The sensor immediately reports back to my Smartthings, alerting me with a timely notification if the water level becomes too...

Remixed from Funflyful's design. ... Holds 4 dosing or airline tubes for 4/6mm pipes can be directly mounted on a 8mm glass tank

http://www.thingiverse.com/apps/customizer/run?thing_id=1572181 Instructions Using the following options: Twist = 2 Mount_hole_dia = 5 tubing_squish_ratio = 0.7 CenterHole_dia = 9 CenterHole_Flat_dia = 4 OD = 65 number_of_teeth_on_planets = 8 P = 40...

http://www.thingiverse.com/apps/customizer/run?thing_id=1572181 Instructions Using the following options: OD = 60 CenterHole_dia = 5.37 Mount_hole_dia = 3 nTwist = 1 tubing_wall_thickness = 1 Mount_Style = 1 tol = 0.15 CenterHole_Flat_dia = 3.67 P =...

I just createt a little mount for a dosing pumpt used for the e-heim vivaline aquarium. ...It fits into the upper frame and stays below the cover plate.

While up grading to a Berd-Air system on my BLV cube I need a good mount to isolate vibrations from my frame. I found a Mount By ShadowX Thing #2849793. I liked the idea but was afraid that the rubber bands would break over time. My kid has Nerf...

station pump

pump case

station pump

pistol pump

pump mdt2009

centrifugal pump

pump_water

Is pump

GP pump

I recently acquired this split type air conditioner/heater from GREE, which surprisingly did not come with a wall mount, so I opted to create one on my own. To take the design to the next level, I've submitted a STEP file for further enhancements.

http://www.thingiverse.com/apps/customizer/run?thing_id=1572181 Instructions Using the following settings: Mount hole diameter is set to 3. Tubing wall thickness is exactly 1. Number of teeth on planets is precisely 7. Mount style has been selected...

frame cover clip where the shells should be able to be clipped into the holder so you don't have to pull up and out, 3 is a half version of the frame cover so you don't have to worry about anything catching, 4 and final is a simple top and side mount...

Design for pump

PUMP NEW MODEL

Design for pump

horizontal split case pump

pump in 3d model

Pump for VT650 Johnston