oneida dust deputy 3d models
17867 3d models found related to oneida dust deputy.thingiverse
Adaptors for Oneida Super Dust Deputy 5" to fit a 5" hose to connect to the Harbor Freight Dust collector inlet, or other applications that use 5" hose 2 Versions, they are basically the same but the larger is 6.5" tall and the smaller one is 3.5"...
thingiverse
this in a flange for shop fox w1661 and using a oneida super dust deputy 4/5 cyclone 6"
thingiverse
This was designed to work as a reducer for the inlet of Oneida's 5" Super Dust Deputy. I designed this to fit internally to the opening to avoid having an internal step down and reduce turbulence. The reducer is sized to fit a 4" flex duct on the...
thingiverse
Customized version of https://www.thingiverse.com/thing:2015939 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2015939
thingiverse
Customized version of https://www.thingiverse.com/thing:2015939 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2015939
thingiverse
This allows you to connect the hose from the Oneida Air Systems Dust Deputy Cyclone kit to a Ridgid wet dry vacuum (specifically the WD4070). Recommend using PETG. ...I used the following print settings: Layer Height: 0.3mm Perimeters: 4 ...
thingiverse
This adapter allows you to connect the hose from the Oneida Air Systems Dust Deputy Cyclone kit to a Ridgid wet dry vacuum (specifically the WD4070). Recommend using PETG. ...I used the following print settings: Layer Height: 0.3mm Perimeters: 4...
thingiverse
This allows you to connect the locking hose from a Ridgid wet dry vacuum (specifically the WD4070) to the Oneida Air Systems Dust Deputy Cyclone. This design doesn't use the locking mechanism of the hose but seals well and holds tight. The elbow...
thingiverse
simple coupler to interface an inventables xcarve dust shoe hose (1.5"ID) to an oneida dust deputy cyclone extractor (2"OD). ...
thingiverse
A nice little adapter from the Festool Sleeved hose to the Oneida dust deputy. Don't forget to add some of the foil tape to keep the ground path! The original design didn't print quite right, but I figured I'd try it anyway. It worked great! Then I...
grabcad
Oneida Air Systems - Dust Deputy dust separator, dust cyclone, dust collector. Did the best I could using calipers and a nice ruler. ...Model units are inch.
grabcad
CNC cuttable 5 gallon bucket lid to fit Dust Deputy cyclone on top of.
grabcad
These are the supports to add to the Dust Deputy to give it a little strength when attaching to a bucket top.
thingiverse
The vacuum hose threads onto the adapter, and the inside is tapered to fit tightly onto the Dust Deputy. It will fit both ports on the dust collector. ...The hose I use is in the following link: ...
thingiverse
The bottom 30 mm attaches to the Dust Deputy as it has a small taper inside that fits the taper on the Dust Deputy. The top 40 mm is where you push the hose into. It is best to add a liberal amount of silicone to the hose end first and let it dry...
prusaprinters
The bottom 30 mm attaches to the Dust Deputy as it has a small taper inside that fits the taper on the Dust Deputy. The top 40 mm is where you push the hose into. ...It is best to add a liberal amount of silicone to the hose end first and let it dry...
thingiverse
Edit: I've reworked the hose connections between the Dust Deputy and the Rigid shop vac to use a section of Rigid 2 1/2" vacuum hose after creating a hose wye for my router table. The .stl files are delineated either DD CH for Dust deputy coil hose,...
thingiverse
... side of the Dust Deputy DIY to a 2" vacuum hose (2.25" OD on vacuum hose). ... It includes cut-outs so that a hose clamp can be used to fix it to the Dust Deputy, and it fits deep onto the Dust Deputy input (which is a 2 step part, it snugs onto both).
thingiverse
Eagle makes several drums that are commonly used with Oneida's DIY Dust Deputy, and the Eagle 1654 is the yellow 20-gallon short and stumpy model. The 30-gallon 1601 and 1602 models also have a 19" diameter top, so I'm pretty sure this would work...
thingiverse
... it to the lid of my bin. ... I wanted to not have to worry about the weight of the Dust Deputy every time that I needed to empty the bin. ... This way, I have the lid connected to a hose which I can just raise and lower without moving the Dust Deputy.
thingiverse
For use with a Dust Deputy Cyclone dust collector, attach the provided connector to the device's horizontal tube and link it to a 2-inch vacuum hose. ...Don't forget to print and place the instructions on your Dust Deputy for easy reference.
thingiverse
Originally intended for the Dust Deputy Cyclone dust collection system, this adapter allows you to use smaller vacuum hoses. Converts 2" O.D. port to a 1.25" O.D port. ... Fix: Updated the dimensions of the small end.
prusaprinters
When I purchased an Oneida Mini-Gorilla dust collector, I found that the adapters available for purchase to connect it to standard 4" hose did not fit, so I created and printed my own. ...Very straightforward print to enable you to connect this device...
thingiverse
Simple, slightly overbuilt, adapter to go from the inlet on a dust deputy to the small sized shop vac hose that came with my 8gal shop vac (ID ~53mm/2in on the connection). ...Should work for a the full 2in hose, but you'll probably loose a bit of...
thingiverse
An adapter for the Dust Deputy DIY cyclonic separator input, to connect a shop vac 2" hose to. This is modeled to the multiple steps of the input, but it really needs a hose clamp to hold it firmly in place. It'll hold well if you firmly press it...
prusaprinters
BackgroundI use an old Festool CT-22 vacuum + Oneida Dust Deputy cyclone separator with my Sawstop PCS and it works well! This lets me avoid having to buy a bulky dust collector and route 4" duct work around my small workshop. I'm sure the newer...
thingiverse
Adapter for DeWalt Stealth Sonic hose to a Dust Deputy 2.5. I added thin neoprene tape on the outside perimeter to help seal. ...YMMV.
thingiverse
This part connects the the 5" Inlet Port for the Super Dust Deputy Dust Extraction Cyclone. ... The larger end connects to the outside of the SDP, and the smaller end allows the 5" hose to connect to it.
thingiverse
A simple support plate modeled to fit the dust deputy where it attaches to a 5 gallon bucket lid. ... Installing this underneath the lid will allow for additional support since a lot of lids are somewhat flimsy.