one hundred concepts scope cap 3d models

Probably buck converters.I printed mine in CF PLA (Extrudr GreenTech Pro CF) and it is rock solid.Use 3-4 perimeters in all parts to ensure stability.Fans:For the hotend fan, you can use the stock one. It's noisy, but it gets the job done.<br>The...

• The pilings/stairs were similarly printed in one piece and then glued to the underside of the floor, (positioning should be obvious as the stairs generally line up with the doors). They are a bit of a pain to print and tidy up though as they...

This is an updated thing, the original one can be found here. The cooling fan duct is the Mistral 2.1a. This main goal of this sensor mount is to bring the SN04 into a position where the entire bed can be measured for mesh-leveling while giving easy...

Once all the extender parts are printed, attach them to the topside of one table and the underside of another tabletop. The 4 pieces with multiple slots for plexi should go on the back and the upper left/lower right and upper right/lower left...

If you run only one type of battery on your Mini Owl, this battery tray can be configured to be bolted to the quadcopter by specifying a bolt shank diameter, bolt head diameter, and bolt head inset. If you run multiple types of batteries, as in my...

iPhone 12 Mini (with leather casing) car holderThis is a phone holder I created for my iPhone 12 mini to be placed in one of the cup holders of my car. I'm driving an Audi A3 but I guess cup holder sizes are standardised.&nbsp;</p><p>The phone holder...

In Larry Niven's The Magic Goes Away, once an area's mana is exhausted, no one can use magic. A common limit invented by Jack Vance in his The Dying Earth series, and later popularized in role-playing games is that a wizard can only cast a specific...

You can use the stock nema 17 extruder motor with the Superfly extruder. All you need is a $15 BMG Clone, and a few M3 screws/nuts/washers Superfly Extuder (https://www.thingiverse.com/thing:4914090) MRF Sailfin Extruder...

02/07/2019 One of the biggest issues that I have had with this design is keeping the wires from rubbing against the rotor. The wire_protector design is somewhat flimsy. So, I designed a new wire/rotor protector that is more rigid. It will also help...

I have designed 2 sets; one for self-tapping M3 and another for M3x4x6.3 brass inserts. I recommend using the brass insert version if you can. There are 2 versions for the mount. adxl and non-adxl. adxl is for Klipper users who want to install...

I don't really need the IR functionality, but I had the camera available, so I used it. Links: How to use the mounting plate to attach the articulated arm to a printed frame (in this case carrying a C270 webcam)...

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part...

This pencil uses a hidden compliant mechanism to hold the lead securely.The biggest design challenge was getting enough grip to hold the pencil lead in place when writingCustom NameYou can add your own name&nbsp;easily,&nbsp;or maybe your company...

you can find the "all sizes" miniature holder here: http://shpws.me/QrLC but for the price you're better off buying one, learning how to use it and printing all sorts of cool things like terrain #Updates ##1.1 (29th jun 17) - added new stand/grip...

So why settle for a generic support system when you can have one that's tailored to your unique needs? Join the 3DPrt Phone Support community today and start crafting a customer experience that sets you apart from the competition. By leveraging the...

It is called V4 and you can find it on this link Prefer a 24v fan like the original one to avoid voltage changes and good quality fans. The added weight compared to the original parts (4010 radial fan and stainless steel shrouds) is +24 grams With...

I scaled the original 51 piece "Japanese Crystal Puzzle" by NacAlain to 1/3 (33.33%) of the original size in three dimensions and I organized all the pieces into one stl to fit on a common Ender 3/Ender 5 sized print bed. (I've also seen the Japanese...

I have noticed that due to this one of my display menus are slightly offset. I am not sure what to suggest here other than tweaking the position of the touch panel if the screen appears to be offset. Printing 1.All Casing elements printed @ 0.2...

I wanted to line up in one row (the last picture), and its very hard to line up the file with a thread. Q: They are to versions of the Blade, v2 and v2.1.... WHY? A: For Printing tolerance reason! The design in digital has both, the inner...

Screw these down until they touch the box, but be careful not to strip the plastic out by over-tightening.Screw your filament receiver (it's pre-threaded) onto the end of one of the tube connectors to seal it off, which leaves space inside for about...

The Garden Gnome: A garden gnome similar to the one broken by Simon's cat in "Let Me In." The gnome is seen holding either a fishing rod or a net. The Bunny: A rabbit that lives in Simon's garden who can literally run circles around the cat. The...

I would highly recommend using reflective tape as it makes the process much faster but the one shown in the images was done with aluminium foil and a glue stick. Make sure when you glue the strips down that they are shiny side up (aluminum foil has a...

Each one of the highly detailed models was meticulously crafted within 3ds Max 2014 and rendered with the latest Vray 3.2 software. This assortment for arranging your outdoor space includes a diverse array of high-quality wooden furniture items...

Or download something like this https://www.thingiverse.com/thing:354723/ (haven't tested if this particulart one fits) Print this duct with 100% Infill, PLA or PETG will do. You need to print it with custom supports as shown in the provided...

(Only one at this point as I only have the Canon to model from) 3.Tubes:: Choice of no tube, 13mm effective, short tube 21mm effective, long tube 31mm effective, long plus short tube 39mm effective, customised. 5.<strong>Lens Mount:</strong> 52mm...

+ one version BL Touch (Offset: X-51 Y-12)The original air duct have not been modified to ensure the same cooling as the original system.This design allows:to adapt to a direct drive and bowden systemto be 15%* faster to print than the original...

you should have 2 wires remaining from the last 2 adjacent coils. NUTS each of the 4 nuts goes into the slot of the case base ROTOR the axel will support 1 or 2 rotors each rotor requires 32 of the magnets, if you want to use less magnets you don't...

Here's how to do it: If you're using Simplify3D, import both files and double-click on one part to open the properties tab. Simply click on "Reset position." Then, click on the second part and repeat the process. After this step, you'll be good to...

One piece contains built-in supports. An optional part without the built-in supports is also supplied if you want to use your slicer supports (see notes below). If you have the proper filament colors, no painting is needed.Two parts require color...

Objectives: Students in 4th-8th grade will be expected to 3-D print the bones included here as well as creating one new bone/piece of their own (this can be done individually or in small groups). Students can use a photo of a bone to design a...