omtech air assist upgrade 3d models

Printed out of PET-G. ... For the fitting (with 1/8" thread) it's necessary to tap 1/8" thread. Recommended to apply a thin layer of silicone to seal top surface of 3D printed part from laser module body, just to avoid air pressure leakage.

... more revision for it to fit and work. ... Designed to eliminate the need for an air tight seal around the laser lense. Also to allow quick fit of interchangeable/custom nozzles without having to remove the whole unit. ... For use with 8mm OD hose.

I changed the input for the air hose a little bit, so that you can print the nozzle without support structures. The opening is suitable for 6mm hoses. For clamping you can simply screw a M4 screw into the hole. This also works without drilling a...

Maximum effective geometry, tip of air action calculated using artificial intelligence. The design is designed for printing without supports. Only 1mm wall width for minimal weight. ... Legs are available here:...

This text describes an air nozzle designed for use with a cost-effective DC-K40 laser cutter. It features an inner diameter of 26 millimeters and has been fitted with a 6 mm silicone tube. ...The connection to the tube is secured by an 8 mm diameter...

Just use you compressor to blow direct air on the engraving point. This design is based on professional laser cutter machines and does not require any extra power source for a fan. ...Just route a hose from your compressor into the dedicated hole and...

needed: PC4-M6 Pneumatic Air Straight Quick Fitting 4mm thread M6 One touch hose Connector Any Outter dia. 4mm tubing, like the ones used for 3d printing. I use OD 4mm ID 3mm tube. Add a small amount of Fun-tak or putty between lens body (not the...

... Did a respin to fit my laser. Closed the opening for the laser barrel(?), shortened to match the overall length of the original plastic eye protector (now removed), and gave the air hose nozzle a little bulking up where it meets the body. ...

This is the design of Alex van Maarschalkerwaart in the FB Group "Atomstack X7 Pro Users Group" This nozzle requires it's companion M5 Nut here: https://www.thingiverse.com/thing:5051175 Here is a youtube video showing the general application and...

... the laser module. Alternatively, I used an M3 heat-press insert instead of a nut. Simply push your air tube into the top and it should sit comfortably! ...The tube is 7.2mm wide (as my tube was 7mm) so should fit any tube diameter below that.

I am using a powerful 12 Volt server fan that blow quite a substantial amount of air at the laser beam. The fan I use blows at 22,000 RPM so it provides plenty of air power. ...

A 4mm attachment is included, suitable for most coiled air hoses. To secure each part firmly in place, apply super glue from below once it's seated. Adding a bit of baking soda will speed up the process instantly. Be cautious not to put any glue on...

This adapter allows directing air onto the workpiece of a laser cutter via a radial fan, preventing buildup on the lens caused by evaporating materials. The part securely attaches by clamping, while one additional screw is used to fix the fan in...

I added similar to support the air feed tube if used. Modified the right side frame “leg” in length to give more stability and a cut out to give finger room to use the module height adjuster thumb screw. As with other small 3D printed parts, very...

I wanted an air assist that didn't use a plastic nozzle on the laser head (for safety reasons) and allowed the use of a quieter air pump. I designed this to work with the LightObject metal air assist nozzle and tinkerneering's 3D printed directed...

This is the most comprehensive Air Venturi Avenger ergonomics upgrade kit available. This will be an ongoing project as there are still a few things that I feel need tweaked but I'm very happy with where it is now. ...This makes the AVA much more...

It directs the air that usally comes from unsealed leaks in the room directly into the air conditioner. The cool air inside and the hot air outside do not mix. Only use with a net. Don't use too much sealing. ... A second pipe probably does not improve...

I modify jacobberlin file and clean it for my OMTech Polar350

To create this unique piece, you can adjust the settings as follows: font size of 10, stick width of 8, message that reads "CLEANUP ASSIST," the "Write" font style from the "Orbitron.dxf" file, a hole radius of 3, stick thickness of 3, a font...

install the printed part on the diode laser. the nozzle is from amazon. perfect fit and secured with the included set screws. ...

Redesigned to fit the Eleksmaker with a quick release laser module holder. Based on this design: https://www.thingiverse.com/thing:1688209 This redesign is necessary due to the newer features of the Eleksmaker. A 50mm x 15mm blower fan, such as the...

The Fusion 360 model is easily accessible at this link: https://a360.co/2xnYMqr

Important... ... Print as it is with supports from build plate only and 3 walls and 60 infill other items needed 25psi compressor https://smile.amazon.co.uk/gp/product/B08JQB7Z9M/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 Hose end ...

To use with my affordable Chinese laser cutter, you'll require this print alongside a Pneumatic 12mm-1/4" BSPT male fitting. Print with two shells for safety; nozzle down orientation is recommended. After printing, heat the fitting while still hot to...

I remixed the original model to adapt it to Atomstack's new M50 laser module and I shortened it by 0.3mm to make the fumes flow better. ...This model fits for X7 Pro A10 Pro and S10 Pro.

Customized version of https://www.thingiverse.com/thing:3764039 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3764039

Rotate like in the picture to print. ...Used in a Fox Alien 4040EX.

Printed @ 80% infill .2 layer height. Added screw holes (3.5mm) to hold in place on your machine. ... Accepts standard airhose Standard 1/8" BSP (its an 8mm thread)

i didn't like the tip of the nozzle being plastic (i only had pla on hand) so increased the nozzle hole to 4mm and used a bit off aluminum tube with the outside diameter of 4mm and inside diameter of 3.2mm. length of tube is 10mm with 3mm sticking...