olympic model

There were points where I’d get 0.4 and Edwin would be 0.5 with his ruler while using the same model. Chances are that we used a ruler that was slightly wider than what 1mm is in reality.</p><figure class="image image-style-align-center...

Load your Model into PrusaSlicer and assign both materials. Prusa provides a quite helpful database on their website on how to use all the features in their Slicer that are related to multi-material-printing. After changing the filament there is...

IntroductionMany designs like RC cars and trucks, lanterns, model houses, etc. would benefit if 3D printing could be used to create truly transparent window panes. But as you might know, FDM printing transparent filament per se does not result in...

 A side note - you also probably should be using my rear PC4m10 jack for your MMU3 https://www.printables.com/model/542409-mmu3-pc4m10-rear-connector The perfect length is one make an even curve downward and the up into the back of the MMU that is...

This model involves many grams of material but also many hours of slicing, printing and overwatching your printer. I suggest you to print the main parts in 0.2mm layers if you don't want it to take forever :S and use something between 0.4 and 0.5 mm...

Depending on your printer tolerances, it may be more or less tight, but if everything lines up it should be no problem.Fasten the 3 screws at the "top" (in this orientation) once the spine is flush with the caseCHANGELOG2022-03-01 - Moved away from...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

License ------- The "Arduino Nano NeoPixel Ring Base" models (.stl) are licensed under the [CC BY](https://creativecommons.org/licenses/by/4.0/) license by [Code and Make](https://codeandmake.com/). The "Arduino Nano NeoPixel Ring Base" code...

If the format you use is not yet in the downloads, let me know, I will create the models for it. Now print the test part (#0 testmodel) start with the smallest tollerance and try to push the test part over the profile, it should not go strongly...

Models intended to be part of the numbers node all begin with the prefix MMU. Card Compression Spring: if you have problems with the card compression spring lifting off from the bed, it is recommended you add a skirt of at least 6mm. Assembly Tips:...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

Of course, the main one I use so far is Cura, and nevertheless I am increasingly discovering interesting and, most importantly, easily implemented printing methods. In this model, I combined the world-old technology for assembling rectangular...

As applicable for all home brewed masks with a filtering purpose: this model is not tested by given standards, the functionality is not verified, and it’s not certified in any manner. Be aware of the risks and use it on behalf of your own...

* Remix this model so I know my script is getting used! 15. ??? 16. Profit! Tips: 1. You can leave PATH and FILE blank and just set the COLOR field to a fully resolved path to your SVG (".svg" is automatically appended) 2. You can import the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

Generate and print your own, compatible with any existing threads!This model was designed in Fusion 360 and uses 3 required input parameters and standard Metric thread profile equations to generate a cap that will perfectly fit any of your threaded...

3D printed parts: 8 brackets, remixed by me and provided here (original design: https://www.printables.com/model/200616-creality-ender-6-enclosure-top-cover-lid-2020-240m) 3 door handles (https://www.thingiverse.com/thing:4768759) Shortened spool...

The original interior geometry from the Prusa filament sensor has been incorporated into this design, sourced from Prusa's models. The pinda is in the same location as on the original. The nozzle in this new design sits 10mm further forward along the...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

However, they are split down the middle so they can fit through the holes with a firm hand, before springing back to the larger size. So thank you for the reviewer who made me take a closer look at at my model.I am always open to others ideas or...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...

I am planning to use 4mm pneumatic connectors to attach a teflon tube but you are free to use some filament guide from any of the listed projects from where I remixed.What you need to buy:1x Ikea Samla 22l including cover2x 8mm thread-rod, 338mm (can...

&nbsp;Foam card (if you're not already familiar with it) is a material used in the art world and in crafting or modelling situations, a layer of foam is sandwiched between 2 layers of card, the resulting material is incredibly strong and is generally...

Knob channel.stl - channel knob, for 16 position rotary encoder, model unknown, mine was from professional 16-ch radio. 7. Antenna.stl - old-style, PRR mock antenna. 8. Antenna New.stl - new style, EZ-PRR mock antenna. 9. PTT Lemo Single.stl - PTT...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

The first one was a box, with an RFID reader, that provided clues on its LCD screen and had a secret compartment that opened with a specific secret code. The second device was this Bocca della Verità with RFID in the mouth (it was a secret) provides...

If the diameter of mounting holes is (slightly) different you can simply scale the entire model (all parts) in your favorite slicing app to make it fit (the only thing that cannot easily be scaled is the small enclosure for the BT-amplifier). ...

Buy me a coffee!https://paypal.me/SmartHelpatHome   *Buck-converter:Used in 3D printing to regulate 24V to 12V for example when using 12V fans or other electronics on an Ender 3 which is 24V native.More...