olight warrior mini holster 3d models

Made a case for a gen 1- Olight Warrior mini. ...Requires 8 3x3mm Magnets for the top and bottom.

Waall mount option for Olight Warrior Mini - non charging

Made for a olight warrior mini and should work for the v2 that came out.

A simple hood for the Olight Warrior Mini 2 to prevent it from accidentally turning on in a bag!

A simple hood for the Olight Warrior Mini 2 to prevent it from accidentally turning on in a bag!

Case for the Olight Warrior mini 2. ... Requires 3mmx20 Dowle pin for hinge and 4, 3x3mm magnets for lid.

A simple hood for the Olight Warrior Mini 2 to prevent it from accidentally turning on in a bag !

A simple end cap to prevent ferrous particles and items from sticking to the charge port on the Olight Warrior mini. ...Allows normal use of the torch (slip off to charge).

Skadis Magnetic Olight Holdersimply put a little 8mm diameter 3mm thickness magnet in the hole    recommanded print setting- perimetar: 3- infill: 15%- support: on- layer height: 0.15mm/0.20mm- filament: PLA, PETGprinted with:...

Belt holster for OLIGHT i3E EOS flashlight

It's an upgraded version of the popular Olight S1/S1R flashlight belt holster, tailored specifically for the Olight S30R model.

->Pictures Holster for the Olight Marauder 2 with Tek Lok for easy carrying on a belt or backpack. The lamp snaps securely into the sleeve, but still rotates inside the sleeve to protect the controls when needed. A tek lok must be purchased...

Tail switch cover for Warrior 3s flashlight. Purpose: to keep magnetic dust particles off the tail switch. ...Snaps on hard and wont fall off.

I also own an Olight R50 Pro Seeker LE, which comes with a charging dock holster that I love using. So, I decided to create one for my M2R Warrior. It printed rapidly and functions flawlessly. The magnetic charger included with the light fits neatly...

This cap fits the Olight Odin Mini or any flashlight with a 27mm diameter bezel. ...Used to avoid accidental light discharges.You print it, you get me a coffee:https://ko-fi.com/gilgsnOr tip me crypto:ETH 0xe7cC2e415E0D2d1De91604B2b693f124dfBCf9B8LTC...

Ring to cover up the connector mount on the back of the Olight Warrior 3 when not using the remote switch.

Printing these at 98% scale with TPU gives a nice snug fit. ... No supports needed.

Final version printed with no raft in PETG but PLA/PLA+ would probably be just fine.If the OLight is loose, use a heat gun to soften the plastic toward the base of the OLight where there's an indentation for the clip and pinch it in. ...Obviously be...

When Olight introduced a modified version of the S1R, I made some adjustments to the holster to accommodate its slightly increased length. The model shown here was printed in translucent red PETG, but standard PLA can also be used successfully. ...The...

TPU Belt holder for the Olight S2 Baton flashlight.  Tested printing on my Prusa i3 with Overture TPU filament. ... After printing, use diagonal cutters to remove the spacers from the belt slot

I have created a protective cap for the Olight Marauder Mini. ... Happy Printing ;-)

The Olight RWX07 switch attaches magnetically to the tail of the Olight M2R Pro Warrior and can become dislodged if it hits something or catches on something. ...This sleeve slides over the tail cap of the flashlight and switch mount to hold them in...

The Olight RWX07 switch attaches magnetically to the tail of the Olight M2R Pro Warrior and can become dislodged if it hits something or catches on something. ...This sleeve slides over the tail cap of the flashlight and switch mount to hold them in...

A charging or just a mount for the Olight M2R Warrior Pro. ...by playing aroundg with color changes, also "glow in the dark" is a litte gimmick ;-)

A charging or just a mount for the Olight M2R Warrior Pro. ... by playing aroundg with color changes, also "glow in the dark" is a litte gimmick ;-)

The spacer is designed to fit an Olight Warrior 3s so that the light no longer falls through the bottom of the holster. The hole in the spacer is sized to allow the light to be used in the holster and the spacer also centers the light too. I simply...

This is a simple holder for the Olight USB charging cable that comes with most of their lights. The base should fit most Baton or a Warrior series flashlights. ...At 0.2mm resolution, the charger should press-fit right into the base with a bit of force...

Charging base for Olight M2R Pro Warrior is being set up. The MCC charger snaps neatly into place within the base, but lacks sufficient grip to remain securely positioned when removing the flashlight. To address this issue, a simple solution could be...

A charging dock or just a mount for the Olight M2R Warrior Pro. by playing aroundg with color changes, also "glow in the dark" is a litte gimmick ;-) Used 4 pieces of 8x3mm neodym magnets for the back https://www.thingiverse.com/thing:4708409 Print...

This is a "traffic" style light cone as an attachment add-on designed to fit the Olight M2R Warrior Light. I have tried the light baton onto the old S30R Baton II and III models and the fit is just a tad looser than the intended M2R Warrior, however...