olight m2r warrior 3d models

This is a "traffic" style light cone as an attachment add-on designed to fit the Olight M2R Warrior Light. I have tried the light baton onto the old S30R Baton II and III models and the fit is just a tad looser than the intended M2R Warrior, however...

... using. ...So, I decided to create one for my M2R Warrior. It printed rapidly and functions flawlessly. The magnetic charger included with the light fits neatly into the dock and is designed to snap securely in place. ...The pocket clip poses no issues.

The Olight RWX07 switch attaches magnetically to the tail of the Olight M2R Pro Warrior and can become dislodged if it hits something or catches on something. ...This sleeve slides over the tail cap of the flashlight and switch mount to hold them in...

The Olight RWX07 switch attaches magnetically to the tail of the Olight M2R Pro Warrior and can become dislodged if it hits something or catches on something. ...This sleeve slides over the tail cap of the flashlight and switch mount to hold them in...

Charging base for Olight M2R Pro Warrior is being set up. The MCC charger snaps neatly into place within the base, but lacks sufficient grip to remain securely positioned when removing the flashlight. To address this issue, a simple solution could be...

Customized version of https://www.thingiverse.com/thing:250899 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=250899

A charging or just a mount for the Olight M2R Warrior Pro. ... by playing aroundg with color changes, also "glow in the dark" is a litte gimmick ;-)

A charging or just a mount for the Olight M2R Warrior Pro. ...by playing aroundg with color changes, also "glow in the dark" is a litte gimmick ;-)

A charging dock or just a mount for the Olight M2R Warrior Pro. by playing aroundg with color changes, also "glow in the dark" is a litte gimmick ;-) Used 4 pieces of 8x3mm neodym magnets for the back https://www.thingiverse.com/thing:4708409 Print...

Adapter do latarki oligrt M2R pozwalający zamienić standardową baterię 18650 na dwie baterie CR123A lub RCR123

I wanted to create a a fun diffuser for my M2R Pro so I created a fun segmented lightsaber, The lightsaber fully extended on the light is about 31 inches long. It is printed as a nest so everything prints together. ...You may want to print with a raft...

The charger magnetically attaches to a slot at the bottom of the flashlight, while the light itself neatly slots into a recess at the top, where it stays charged.

Made a case for a gen 1- Olight Warrior mini. ...Requires 8 3x3mm Magnets for the top and bottom.

Tail switch cover for Warrior 3s flashlight. Purpose: to keep magnetic dust particles off the tail switch. ...Snaps on hard and wont fall off.

Waall mount option for Olight Warrior Mini - non charging

Made for a olight warrior mini and should work for the v2 that came out.

Case for the Olight Warrior mini 2. ... Requires 3mmx20 Dowle pin for hinge and 4, 3x3mm magnets for lid.

A simple hood for the Olight Warrior Mini 2 to prevent it from accidentally turning on in a bag!

A simple hood for the Olight Warrior Mini 2 to prevent it from accidentally turning on in a bag!

Ring to cover up the connector mount on the back of the Olight Warrior 3 when not using the remote switch.

A simple hood for the Olight Warrior Mini 2 to prevent it from accidentally turning on in a bag !

A simple end cap to prevent ferrous particles and items from sticking to the charge port on the Olight Warrior mini. ...Allows normal use of the torch (slip off to charge).

This is a simple holder for the Olight USB charging cable that comes with most of their lights. The base should fit most Baton or a Warrior series flashlights. ...At 0.2mm resolution, the charger should press-fit right into the base with a bit of force...

Tested on Warrior 3 and Warrior 3S.

The spacer is designed to fit an Olight Warrior 3s so that the light no longer falls through the bottom of the holster. The hole in the spacer is sized to allow the light to be used in the holster and the spacer also centers the light too. I simply...

Skadis Magnetic Olight Holdersimply put a little 8mm diameter 3mm thickness magnet in the hole    recommanded print setting- perimetar: 3- infill: 15%- support: on- layer height: 0.15mm/0.20mm- filament: PLA, PETGprinted with:...

Support pour Olight sROD Contacteur Déporté Magnétique À Fil Long Pour JAVELOT PRO 2 / WARRIOR 3 / WARRIOR 3S / WARRIOR X 3 / ODIN GL M Le Olight sROD est un contacteur déporté magnétique pour JAVELOT PRO 2 / WARRIOR 3 / WARRIOR 3S / WARRIOR X 3 /...

The Model PCP Ataman M2R is a high-performance pre-charged pneumatic air rifle that boasts an impressive design and remarkable accuracy. It features a two-stage adjustable trigger, manual safety, and ambidextrous cheek piece for comfortable shooting....

Printing these at 98% scale with TPU gives a nice snug fit. ... No supports needed.

Hello, Here is my diffuser for the Olight S30R III lamp Printed with Glow in the Dark from Amolen